on 07-16-2008 1:29 PM
Hi
I am in the process of upgrading a new Solution Manager 4.0 SR 2 system from Support Pack Stack 10 to 15. But I am getting the following it is asking for a DUMMY CRT to resolve the conflick between suport packs SAPKITL425; SAPKB70014 and SAPKU50011.
I have looked for this dummy CRT on the SAP Market Plase with no success.
Has any one had this problem and if so how did you fix it?
Thank you
Dawid
Some more info.
Phase ADDON_CONFLICTS_?: Explanation of Errors
Conflicts were found between the Support Packages that you want to
import and the Add-Ons installed in the system. To guarantee the
consistency of your system, the import is interrupted until all Conflict
Resolution Transports (CRTs) for the listed Support Packages are
included in the queue.
To include the CRTs in the queue, proceed as follows:
- Write down the Support Packages and Add-Ons that have conflicts.
- Leave this screen by choosing 'Cancel' (F12).
- Load the CRTs for the Support Packages with conflicts from the SAP
Service Marketplace or request them from your Add-On supplier.
- Define the extended queue again in the Support Package Manager.
- Import the queue. The Support Package Manager executes all steps from
the beginning.
If the problem involves an SAP Add-On, see SAP Note 53902, which tells
you which CRTs resolve the conflicts. Otherwise contact the supplier of
your Add-On for details on how to proceed.
The following contains a table of Support Packages for each Add-On for
which conflicts were detected. The column 'Information on the Conflict
Resolution' specifies how you can resolve a conflict. For more
information, select the corresponding 'Information for the Conflict
Resolution'.
Conflicts Between Add-On ST-SER 700_2006_2 and Support Packages
Component Release Support Package Information on
Conflict Resolution
ST 400 SAPKITL425 CRT: DUMMY
Conflict resolution by including the CRT DUMMY for Add-On ST-SER rel.700_2006_2
Message no. TN433
Diagnosis
The conflict check detected conflicts between the Add-On ST-SER release 700_2006_2 and the OCS Package SAPKITL425.
System Response
The system stops processing the queue.
Procedure
In order to resolve these conflicts, include the Conflict Resolution Transport (CRT) DUMMY of the Add-On ST-SER release 700_2006_2 in the queue:
If it is an SAP Add-On, look for a CRT DUMMY in the Software Distribution Center of the SAP Service Marketplace (http://service.sap.com/swdc).
If it is a third-party Add-On, contact the Add-On vendor and ask about the availability of the CRT DUMMY.
If the CRT is not available, you must remove the Support Package SAPKITL425 from the queue.
Some more info.
Phase ADDON_CONFLICTS_?: Explanation of Errors
Conflicts were found between the Support Packages that you want to
import and the Add-Ons installed in the system. To guarantee the
consistency of your system, the import is interrupted until all Conflict
Resolution Transports (CRTs) for the listed Support Packages are
included in the queue.
To include the CRTs in the queue, proceed as follows:
- Write down the Support Packages and Add-Ons that have conflicts.
- Leave this screen by choosing 'Cancel' (F12).
- Load the CRTs for the Support Packages with conflicts from the SAP
Service Marketplace or request them from your Add-On supplier.
- Define the extended queue again in the Support Package Manager.
- Import the queue. The Support Package Manager executes all steps from
the beginning.
If the problem involves an SAP Add-On, see SAP Note 53902, which tells
you which CRTs resolve the conflicts. Otherwise contact the supplier of
your Add-On for details on how to proceed.
The following contains a table of Support Packages for each Add-On for
which conflicts were detected. The column 'Information on the Conflict
Resolution' specifies how you can resolve a conflict. For more
information, select the corresponding 'Information for the Conflict
Resolution'.
Conflicts Between Add-On ST-SER 700_2006_2 and Support Packages
Component Release Support Package Information on
Conflict Resolution
ST 400 SAPKITL425 CRT: DUMMY
Conflict resolution by including the CRT DUMMY for Add-On ST-SER rel.700_2006_2
Message no. TN433
Diagnosis
The conflict check detected conflicts between the Add-On ST-SER release 700_2006_2 and the OCS Package SAPKITL425.
System Response
The system stops processing the queue.
Procedure
In order to resolve these conflicts, include the Conflict Resolution Transport (CRT) DUMMY of the Add-On ST-SER release 700_2006_2 in the queue:
If it is an SAP Add-On, look for a CRT DUMMY in the Software Distribution Center of the SAP Service Marketplace (http://service.sap.com/swdc).
If it is a third-party Add-On, contact the Add-On vendor and ask about the availability of the CRT DUMMY.
If the CRT is not available, you must remove the Support Package SAPKITL425 from the queue.
Dear
Please read following oss notes
Note 662441 - Solution Manager: SAP Notes for Support Packages
Section: ST 400 SP15 (SAPKITL425)
The answer is there, short explanation: You need to use transaction SAINT instead of SPAM if you want to upgrade your ST-SER release (from 700_2006_1 to a higher version).
There is no CRT available to solve this conflict.
Please read the note for full explanation and for the steps you need to follow to resolve the situation.
Kind regards
Tom
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
91 | |
10 | |
10 | |
9 | |
9 | |
7 | |
6 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.