R/3 to XI- IDOC posting

[Former Member]

I am sending the standard Idoc ORDERS from R/3 to XI.When I post the IDOC from transaction WE19. It shows that IDOC is sucessfully sent and saved.

but when i check the message in XI by I enter Message ID: ORDERS, I am getting this popup "No message selected"

thnx

Anmol

[Former Member · Accepted solution]

Hi Anmol

In SM59 please check your user name and password once again. Now it is the problem between R3 and XI.

Please go through following thread

Regards

Abhishek Mahajan

***Please reward points if helpful*

[sunil_singh13]

Hi Anmol,

There Could be two possible reason for your problem

1) Your entering wrong Message ID

2) Your Message has not reached in XI.

Try to execute Moni on Date time basis.

And Perform all the checks to confirm that your Idoc has reached to XI.

Reward points if Helpful

Thanks

Sunil Singh

[former_member556603]

Hi,

Check this,

/people/ravikumar.allampallam/blog/2005/02/23/configuration-steps-required-for-posting-idocsxi

Thanks,

Satya

[vijay_b4]

Hi Anmol,

In SM59 please check your user name and password once again. Also please test the connection by clicking on Test Connection. Also from R3 it is successful because it has sent succesfully. Now it is the problem between R3 and XI.

think you have not done the settings between R3 and XI to send Idocs. Check this links where you have to do all these settings to get Idoc from R3 to XI:

https://www.sdn.sap.com/irj/sdn/wiki?path=/display/xi/sapR3%28Idocs%29ToXI--Steps+Summarized&

In R3 check SM58 whether there are any errors? Also see your queues smq1 whether there are any block queues or not?

Also see smq2 in XI.

Reward points if this helps

Regards

Pragathi.

[former_member859847]

Hi,

Please check the entry of IDOC in IDX5 of xi.

make sure that,please load the metadata of IDOC in IDX2 .

regards

mahesh.

[Former Member]

HI,

1. Start with checking the status in sm58 of sender R/3

Follow the steps

2. Try deleating the IDoc from IDX2 and refiring the same.

3. Check your RFC destination definition (the one pointing to your XI server) to confirm that it is of type '3' (R/3 system) and not 'T' (TCP/IP).

In your ID, in the Sender Business System --> Adapter Specific Identifiers, give the logical name for the business System pointing to the R3 system

4. Monitor the SM58 in R/3 for IDOC status.

Refer below links for indepth troubleshooting

Refer below steps

/people/prateek.shah/blog/2005/06/08/introduction-to-idoc-xi-file-scenario-and-complete-walk-through-for-starters

Thanks

Swarup

[Former Member]

Hi,

check in Sxmb_moni directly, by giving from and to Date.

but when i check the message in XI by I enter Message ID: ORDERS, I am getting this popup "No message selected"

I think this is not the way u have to search in moni.

Regards,

Pradeep A.

[Former Member]

Hi,

plz chk the ALE settings that you have done....

Steps for ALE settings:-

Steps for XI

Step 1)

Goto SM59.

Create new RFC destination of type 3(Abap connection).

Give a suitable name and description.

Give the Ip address of the R3 system.

Give the system number.

Give the gateway host name and gateway service (3300 + system number).

Go to the logon security tab.

Give the lang, client, username and password.

Test connection and remote logon.

Step 2)

Goto IDX1.

Create a new port.

Give the port name.

Give the client number for the R3 system.

Select the created Rfc Destination.

Step 3)

Goto IDX2

Create a new Meta data.

Give the Idoc type.

Select the created port.

Steps for R3.

Step 1)

Goto SM59.

Create new RFC destination of type 3(Abap connection).

Give a suitable name and description.

Give the Ip address of the XI system.

Give the system number.

Give the gateway host name and gateway service (3300 + system number).

Go to the logon security tab.

Give the lang, client, username and password.

Test connection and remote logon.

Step 2)

Goto WE21.

Create a port under transactional RFC.(R3->XI)

Designate the RFC destination created in prev step.

Step 3)

Goto SALE.

Basic settings->Logical Systems->Define logical system.

Create two logical systems(one for XI and the other for R3)

Basic settings->Logical Systems->Assign logical system.

Assign the R3 logical system to respective client.

Step 4)

Goto WE20.

Partner type LS.

Create two partner profile(one for XI the other for R3).

Give the outbound or inbound message type based on the direction.

Step 5)

Not mandatory.

Goto BD64.

Click on Create model view.

Add message type.

Step 6)

Goto WE19

Give the basic type and execute.

fill in the required fields.

Goto IDOC->edit control records.

Give the following values.(Receiver port,partner no.,part type and sender Partner no. and type)

Click outbound processing.

Step 7)

Go to SM58

if there are any messages then there is some error in execution.

Goto WE02.

Check the status of the IDOC.

Goto WE47.

TO decode the status code.

BD87 to check the status of IDOC.

In case if not authorized then go to the target system and check in SU53, see for the missing object

and assign it to the user.

SAP r3

sm59(status check)(no message)

WE02(status check)

WE05(status check)

BD87(status check)

Xi

IDx5(Idoc check)

SU53(authorization check)

reward points if helpful....

PrasHanT