on 05-08-2008 8:11 AM
Hi All,
While doing RFC as Receiver, do we need to do any extran settings for SAP System side??
is there any things we need to check like some services are active or not and any thing even it is small also
Regards
Suman
Hi Suman,
1) In this case the most common error that we do is to forget the funtion to make Remore enabled ........so take care of this...........
2) Check and test the RFc destination in SM59.........also test FM in the SE37 ...check if the logic is rightly excuted or not.....
And also activate all the objects created
All the best
Regards
Sai
Reward with points if helpful
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Heyy Sai,
1) In this case the most common error that we do is to forget the funtion to make Remore enabled ........so take care of this...........
Its already Remotely enabled, thats why iam able to import it into IR at the time of Design
2) Check and test the RFc destination in SM59.........also test FM in the SE37 ...check if the logic is rightly excuted or not.....
Do we really require any RFC Destination in case of RFC is the Receiver???
And also activate all the objects created
I activated all the Objects
Regards
Suman
Perform the following checks.
1. RFC is Remote Enabled and have no problem with its execution.
2. Strucutre Imported in XI /PI is consistent with the RFC in SAP system.
3. The User Credentials u specify in ReceiverComm Channel of XI should have S_RFC Role or Authorization in SAP System.
Regards,
Ashwin M
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
You configure the receiver RFC adapter so that you can use it to convert XML messages from the Integration Server or the PCK to RFC calls and send these calls to the corresponding receivers.
You configure the adapter on the Parameters tab page during the definition of a communication channel in the Integration Server or in the PCK. In addition to the adapter configuration, on the Module tab page in the module processor, you can specify generic modules, which give the adapter additional functions.
Prerequisites
...
1. You have created a new communication channel or have opened an existing one.
2. On the Parameters tab page you have selected the adapter type RFC.
3. You have selected the Receiver radio button to define the adapter as a receiver adapter.
4. The communication channel in which the RFC adapter is defined must be defined for a service of type Business System in the area Service Without Party. In the PCK you must create an empty party record.
The entries made in the communication channel must be identical to those for the adapter-specific identifiers for the business system. For more information about adapter-specific identifiers, see: Service in the Integration Server or Service in the PCK.
Activities
Transport Protocol
The transport protocol is RFC.
Message Protocol
The message protocol is RFC (RFC XML).
Adapter Engine
Select the Adapter Engine on the Integration Server, or select a non-centrally installed Adapter Engine. This selection is not available in the PCK.
Target Tab Page
RFC Client Parameters
The RFC client parameters identify the receiver system.
Specify the type of the RFC server.
● It can be an SAP System.
● It can be an External RFC Server.
The external RFC server is a server programmed with RFC-SDK that has registered itself with an SAP Gateway.
If your SAP system works with load balancing, select Load Balancing.
For more details , have a look into this link
http://help.sap.com/saphelp_nw04/helpdata/en/c8/e80440a832e369e10000000a155106/content.htm
Regards
Aashish Sinha
PS : reward points if helpful
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
i have done IDOC--File scenario and i used one Business system for that scenario. Its all fine
Now In HTTPRFC Scenario, iam using the same Business system which i used in the IdocFile scenario
In this case iam interacting with the same SAP R3 server & same client only
Is there any problem with this Business system because of using the same for two cases
Regards
Suman
User | Count |
---|---|
81 | |
10 | |
10 | |
9 | |
7 | |
6 | |
6 | |
5 | |
4 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.