ST04 not working

[Former Member]

hi

as per my daily monitoring, i tried to see buffer quality through ST04 code, it was not displaying any values and DYNPRO FIELD dump is coming and program terminating.

can i know the reason and wt could be the solution.

regards,

Sudhakar K

[Former Member]

Hi

The best way to check table space,you can use brtool to do that.

Sukrut S

[fidel_vales]

Hi,

It could be very interesting if you provide (much) more information.

what is your oracle version?

what is your SAP basis version and support package?

do you get directly the dump after starting ST04 or do you something else?

Was it working before?

If so, Have you done something after the last time you saw it working?

Could you be a bit more specific about the dump (paste here the first 20 lines)? I think "DYNPRO FIELD" is not a complete nor accurate description

Have you check for SAP notes?

[Former Member]

hi

my sap version is ECC 6.O and current patch level is 13.

regards,

Sudhakar

[fidel_vales]

And ....

what about the other questions?

My apologizes for asking, but I have forgotten my crystal ball in the other suit

Please, please, please. Help me to help you

[Former Member]

hi

actually 3 months back we upgraded from 4.6c to ECC 6.0

it was working before.

ya the dump is coming directly

please help out ASAP.

regards,

sudhakar k

[fidel_vales]

OK,

In one reply I asked for more information.

you did not provide it

Next reply I asked for the same information

you did not provide it

then you said:

please help out ASAP.

SO I'll put my Harry Potter hat, try to use my crystal ball (and I promise to put your name in the black list) and do something I do not like at all, guess

I'll answer some of my own questions

>It could be very interesting if you provide (much) more information.

>what is your oracle version?

You mention that you have ECC 6.0.

This is kernel 700, so you should be using 10.2.0.2

>what is your SAP basis version and support package?

You mention that you have ECC 6.0, therefore the basis version should be 700

You mentioned that your patch level is 13. I guess you meant that your support package version is 13.

>do you get directly the dump after starting ST04 or do you something else?

Good, the dump comes when you start ST04

>Was it working before?

Yes

>If so, Have you done something after the last time you saw it working?

Upgrade from 4.6C to ECC 6.0

>Could you be a bit more specific about the dump (paste here the first 20 lines)? I think "DYNPRO FIELD" is not a complete nor accurate description

NO, "I do not know how to paste the first 20 lines of the dump. I do not care if the "DYNPRO FIELD" is an accurate description of the issue we have, you know it all, so you should be able to guess what my problem is".

>Have you check for SAP notes?

"No, what for? I write the question in the Oracle Forum and someone will start shooting answers, perhaps someone guess my problem and gives a correct solution."

So, without the dump information, perhaps you are lucky and the following two notes solve your problem:

1045804 ST04N and DBACOCKPIT crash due to anormal buffer quality

1156105 st04n crashes due to a negative value of buffer busy waits.

Perhaps you are unlucky and

• you have to provide more information.

• you pray to "GOD" to illuminate us so we can provide you the correct answer with insufficient information.

• you open a customer message on SAP (upgrading first to the latest support package)

[Former Member]

hi fidel

it was my mistake that I did not provide proper information to you, becuase i was in hurry to solve the issue.

Thankig you for the reply.

Anyway, sorry for cuasing inconvenience

reagrds,

Sudhakar K

[Former Member]

LOL!!!!

this supersedes all the sarcasm that i've seen so far on the forums.

poor guy...

[Former Member]

Hi. First chek in st22 and sm21messages. Are the tablespace is good (not full ?) . Any other errors form other t-codes? Regards.