on 04-28-2008 9:28 PM
Hi,
I activated POS 9ASNPBAS and initialized PA 9ASNP02 for version 000. Now I go into SNP94 and create a selection with version 000 and load. I am getting the following error. It says "The key figure 9ADFCST is not assigned to any of these SNP aggregates in the 9ASNP02 planning area." But the PA is a standard one I haven't even changed it. I checked in 9ASNP02 and the 9ADPFCST is not assigned to the aggregates mentioned. Shouldn't the standard system be delivered with 9ADPFCST in the aggregates? or is ithis a note?
Conflict identified between selection and key figures to be read
Message no. /SAPAPO/MSDP_PB230
Diagnosis
Your selection conditions in the shuffler encompass the following SNP aggregates:
9AMA as Display attribute of the object selection
9AMA as an extended condition of the object selection
The key figure 9ADFCST is not assigned to any of these SNP aggregates in the 9ASNP02 planning area.
System Response
The system does not read any transaction data
Procedure
Choose a different selection condition or change to a different data view.
Thanks.
Hi - presume you release from DP to SNP for pplanning purposes, in which case the key figure should be populated.
Refer extract from help as given beneath:
From the SAP Easy Access Menu, choose Demand Planning ® Environment ® Release to Supply Network Planning, and then choose the Release: Enhanced icon. The Data Transfer: Time Series Order Network screen appears.
2. You enter the source planning area, source planning version and target planning version.
The planning area 9ASNP02 (the standard planning area for order-oriented planning) is used as the target planning area. Therefore, all of the specified target key figures are contained in 9ASNP02.
3. You specify From and To Dates to define the beginning and end of the release horizon.. These dates are mandatory.
4. You specify a planning buckets profile.
The use of a planning buckets profile for the release from DP to SNP is optional. If you use a planning buckets profile, the system releases the demand plan in the buckets in which data was planned. The timeframe of the planning buckets profile must be as big as, or bigger than, the release horizon specified in the From and To dates.
If you do not enter a planning buckets profile, the data is read in technical periods. The storage buckets profile determines what the technical periods are. Technical periods are not visible to the user.
5. Enter the products or range of products for which you wish to release the plan.
This setting is optional. If you do not make an entry here, all products in the model of the specified planning version are used.
6. Enter the locations or range of locations for which you wish to release the plan.
This setting is optional. If you do make an entry here, all locations is the model of the specified planning version are used.
7. Choose the Key fig. assignm. icon to assign the key figures to order categories. For more details about the key figure assignment, see below.
8. Set the Log indicator, if you wish to view the results from the release.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
I am loading wrong selection it seems. I was trying to load data to show all Products for Version 000 and a Plant. Apparently I should I taken a Product also at the same time. When I included Product in selection, it worked.
Thanks for all the help.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi visu,
I am also getting the same error as what visu told.
so i created simulated planning area and choosen 9adfcst as a a key figure. even though also i am getting the same error.
"conflict identified between selection and keyfig.when i press help.Your selection conditions in the shuffler encompass the following SNP aggregates:
9AMA as Display attribute of the object selection
as an extended condition of the object selection
The key figure 9ADFCST is not assigned to any of these SNP aggregates in the 9RAO_TEST planning area.
ues to be read".
what is the problem?I used interchangeabilty concept FFF class.I choosen only product in selection. it is not working
please let me know.9ama is not avaialble in 9asnp02 and my simlated planning area
Hi
Are you just using the Material attribute in Show? The aggregate level 9AMA is not associated with 9ASNPBAS in the standard system. If you use APO - Location Product in the show selection that key figure should be on that aggregate level 9AMALO as standard.
Ian
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
8 | |
4 | |
3 | |
2 | |
2 | |
1 | |
1 | |
1 | |
1 | |
1 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.