Can anyone tell me how an ALE configuration can be set on one client only?

[Former Member]

I am trying to create a scenario which requires to configure one client

[Former Member · Accepted solution]

First you have to create a dummy logical system name

Go to customizing and select Basis-Distribution(ALE)- PRepare Sending and Receiving Systems-Set Up Logical System

Give this logical System a name

This dummy Logical system will serve as receiver system in distribution scenario

Please feedback if this information was usefull

[Former Member · Accepted solution]

do I need to create a Distribution View for it also?

Plz tell me the whole procedure.

[nisarkhan_n · Accepted solution]

yes you have to create it....check this blog from 3 rdsteps it takes you tought that details

http://searchsap.techtarget.com/tip/0,289483,sid21_gci1242945,00.html

[Former Member · Accepted solution]

Yes we need to create a Distribution View for it,

Use the Transaction Id BD64 with the previous Logical system as sender and the "dummy" logical system as receiver.

Please take care of the names.

After that you generate Partener Profile for newly created distribution view using Tid BD82

this step will generate outbound parameters, later you can use Tid WE20 to create inbound parameters

Hope this solves your querry

[Former Member · Accepted solution]

Hi,

Goto BD64

1) Create a Distribution Model by selecting ‘Create Model View’:

2)Specify the name of the model view and a description.

3) Select Sender/Receiver/message type.

Distribution model is required for outbound case.

Thnx

Chirag

[Former Member · Accepted solution]

Thanx Sourabh, I was actually stuck at this point only

[nisarkhan_n · Accepted solution]

I would suggest you to check the lnks properly....since you were stuck in the data modelling view step ......all the information are in links.

you cannot give any receiver name name in that, it should be the LS name of the XI....

[Former Member]

Sushama,

1)Goto BD64

2)Create already existing logical system as SENDER

3)Create dummy logical system as reciever

4)Goto BD82 and the outbound parameters will be created

5)Goto WE20 to create the inbound parameters

[Former Member]

Hi,

Please follow these steps:

For File to IDOC,

in R/3

1.create rfc connection using sm59

2.create Logical sys using bd54

3.create port using we21

4.create partner profile using we20

in xi

1.create rfc connection using sm59

2.create Logical sys using bd54

3.create port using IDX!

for IDOC to FIle

R/3 side

1.create rfc connection using sm59

2.create Logical sys using bd54

3.create port using we21

4.create partner profile using we20

5.distribute busynessmodel using bd64

1.create rfc connection using sm59

2.create Logical sys using bd54

3.create port using IDX!

4.create partner profile using we20

Also refer these links:

ALE configuration for pushing idocs from SAP to XI

/people/swaroopa.vishwanath/blog/2007/01/22/ale-configuration-for-pushing-idocs-from-sap-to-xi

IDOC testing using WE19

/people/sameer.shadab/blog/2005/07/25/reposting-idocs-instead-of-recreating--for-testing-purpose-xi

File To IDOC - Part1 (SLD and Design):

https://www.sdn.sap.com/irj/sdn/wiki?path=/display/profile/2007/05/11/fileToIDOC&

File To IDOC - Part2 (Configuration):

https://www.sdn.sap.com/irj/sdn/wiki?path=/display/profile/2007/05/11/fileToIDOC-Part2+(Configuration)&

File To IDOC - Part3 (Steps required in XI and R3):

https://www.sdn.sap.com/irj/sdn/wiki?path=/display/profile/2007/05/11/fileToIDOC-Part3(StepsrequiredinXIandR3)&

https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/d19fe210-0d01-0010-4094-a6f...

regards,

Nithiyanandam

[Former Member]

Hi Sushma,

Check this BLOG for ALE Settings

/people/swaroopa.vishwanath/blog/2007/01/22/ale-configuration-for-pushing-idocs-from-sap-to-xi

REgards

Seshagiri

[nisarkhan_n]

For the detail step on performing refer the below link with screen shots.

For configuring the IDOC: http://searchsap.techtarget.com/tip/0,289483,sid21_gci1242945,00.html