message is not going from BPM.....

[Former Member]

Hi all,

I am doing File to file thro' RFC using BPM....as i have already mentioned in my previous thread.

Do i need to create any sender/recvr agrrement ffor BPM to R/3.???

please refer my previous thread!!

sam

[Former Member · Accepted solution]

Hi

as per ur scenario u r calling the RFC at the R/3 system check whether that system is up.

and one more thing if the system is up then check the RFC that u r using

login to the R/3 system

go to transaction se37

enter theRFC name and execute.

enter the input value

check whether the response is coming back or not.

and in XI u also have to create the receiver determinatiopn from BPM to R/3 system

and corresponding interface determination is also required.

u also have to create the receiver agreement.

if u still face the problem please reply me back.

Thanks

Rinku

[Former Member · Accepted solution]

Hi rinku,

i have created..already.. ..evrything is fine..

i have checked the RFC checked evrytthing...is ok...

actually nothing is showing in MONI or RWB..

dono whats the problem...

i have checked the rcvr RFC comm channel in comm channel monitoring.... its showing red.......

actually first time when i tested the scenario.. in moni .. i got error msg abt RFC cmm channel.. (i putted ENG instead of EN).. then i changed it.. again testd.. then onward.... i didn;t get any message from BPM to R?3...

[Former Member · Accepted solution]

Hi Sam

In the RFC receiver adapter u have to define the same parameters

application server --->will be the server address of the R/3 system on which the RFC is available

System number -->will be ur R3 system no

Authentication mode--->use logon data for SAP system

Logon User-->user name for the RFC system

Logon password--->password for the same system

Logon Language-->EN

Logon Client-->whatever ur client number

Maximum connection --->1

use the following information to configure the adapter.

if still face the problem please reply me back,

Thanks

Rinku

[Former Member]

Hi,

Do i need to create any sender/recvr agrrement ffor BPM to R/3.???

You need to define the sender and Receiver agreements for RFC and files. The communication will not be from BPM to R/3. its Fiel to R/3 via BPM in XI.

As your concern is about the message is not getting reached to R/3.

Have you check in SXMB_MONI_BPE. also monitor if the message is not stuck up in the queue at SMQ1 or SMQ2

In RWB check if the fiel is successfully picked up from sender and there also you could monitor the Integration Process Engine.

Thanks

Swarup

Edited by: Swarup Sawant on Feb 27, 2008 9:58 AM

[Former Member]

hi swarup/rinku

You need to define the sender and Receiver agreements for RFC and files. The communication will not be from BPM to R/3. its Fiel to R/3 via BPM in XI.

i am total agrre with u....

but BPM is also a service right...

when i run the scenario in moni ishould get 3 sender sys.

1)file sender

2)BPM

3)R/3

actually my flow is FIle->XI(BPM)->R/3->XI(BPM)->FIle

but for BPM to R/3 i donth think sender agrrement in required

i am unable to create sender agrrement for BPM to R/3 as.. i need to provide sende r comm channel.. and there nothins is displaying.. please give some solution...

Thanks

[Former Member]

SA and RA need to be create if you are creating communication channels

so in your scenario...file to file using BPM u have to create one SA and one RA

but u have to create two Receiver Determination

1.File to BPM

2. then BPM to File

Thanks

Farooq

[nisarkhan_n]

You are dng an RFC lookup right?

Explain me your sceanrio, had a look into prevous discussion.

explain the scenarion and steps you have followed till now.

[Former Member]

no nisar.. am not using rfc look up.....

i have referd blo numbe r 1926..