on 12-11-2007 8:45 AM
In mapping based MessageSplit
how to createInterfaceDetermination,ReceiverDetermination.In My Scenario one sender, 2 Receivers.
Now How many InterfaceDetermination's,ReceiverDetermination's have to be create
Hi mahesh
You will have to make 3 communication channel one corresponding to the sender and to corresponding the receivers. There will be one Receiver determination , one interface determination where the type of interface determination will be enhanced in nature instead of standard, there will be one sender agreement and two receiver agreements .
hope your problem is solved . Points rewarded will be appreciated.
take care and god bless
joel anthony trinidade
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Mahesh,
There will be <b>One Receiver Determinaion</b> and <b>Two Interface Detemination</b>.
In Receiver Determination you give your 2 receivers which are going to receive the message.
Regards,
Sarvesh
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Go through this blog.
/people/srinivas.vanamala2/blog/2007/02/05/step-by-step-guide-xml-file-2-xml-file-scenario-part-ii
For your two "<b>Receiver systems</b>", you need to add these systems in Receiver Determination. In order to do that select the Help option from the <b>Service</b> option in <b>Configured Receivers</b> and select the receivers.
Regards,
Sarvesh
Hi Mahesh,
having performed your message mapping ,, used in interface determination(by linking it with the help of interface mapping via configuration).
You can decide on the value in the payload to which receiver the message should go.
Use following scenarios, may help you:-
/people/venkat.donela/blog/2005/03/03/introduction-to-simple-file-xi-filescenario-and-complete-walk-through-for-starterspart2
/people/venkat.donela/blog/2005/03/02/introduction-to-simplefile-xi-filescenario-and-complete-walk-through-for-starterspart1
/people/daniel.graversen/blog/2006/12/29/hack-using-xpath-in-xi-message-mappings
/people/bhanu.thirumala/blog/2006/02/02/graphical-message-mapping-150-text-preview
/people/srinivas.vanamala2/blog/2007/02/05/step-by-step-guide-xml-file-2-xml-file-scenario-part-ii
/people/srinivas.vanamala2/blog/2007/02/05/step-by-step-guide-xml-file-2-xml-file-scenario-part-i
/people/divya.vidyanandanprabhu/blog/2005/06/28/converting-xml-to-pdf-using-xi
/people/venugopalarao.immadisetty/blog/2007/01/24/troubleshooting-file-to-idoc-scenario-in-xi
/people/prateek.shah/blog/2005/06/08/introduction-to-idoc-xi-file-scenario-and-complete-walk-through-for-starters
Vishal
Reward points for useful Reply
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
hi mahesh,
u need to give two receivers in rec determination. for both of the rec u need interface determination (so in ur case 2). this will be an enhanced interface detn.
[reward if helpful]
regards,
latika.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
hi mahesh,
go to rec determination and give ur recs (give conditions if u need msg to be routed to a rec only for certain conditions). click on each receiver and u can specift in interfaces for that receiver at the bottom of screen (right click-- new specific...remember !! ) ) on int det screen u can specify it as enhanced...(radio button) specify interface mapping. same for other rec.
refer:
http://help.sap.com/saphelp_nw04/helpdata/en/14/80243b4a66ae0ce10000000a11402f/frameset.htm
[reward if helpful]
regards,
latika.
User | Count |
---|---|
85 | |
10 | |
10 | |
10 | |
7 | |
6 | |
6 | |
5 | |
4 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.