Unable to Receive the File into Target Directory Using FTP

[Former Member]

Hi All,

Here I Did Simple File-File Scenario With FTP.

Iam Able to Pick the File From the FTP Location And File has been Deleted From Source Location ( Set the Processing Mode as Delete ).

Unable to See the Pipeline Steps in Moni, But Able to Se the Success Message With the Inbound Payload only.

Also chked with the comm. channel of sender and receiver, where the sender shows the message process details but not the receiver comm. channel.

Regards

Giri

[Former Member]

Hi Giri,

i don't remember the exact error but it is related to source structure used in the Mapping and structure which is coming from the fileserver, which doesn't match with the DT created.

Did you test the MM with the incoming file data? if not copy the data in the file and test it in MM and check.

Regards,

Karan.

[Former Member]

Hi Giri,

Check the MM after picking the file from fileserver. i faced same problem once and when i checked my MM there is an error pop up in MM.

Regards,

Karan.

[Former Member]

Hi,

<i>faced same problem once and when i checked my MM there is an error pop up in MM.</i>

What Type of Error You got, Can you Please Give some Idea about this.

Regards

Giri

[Former Member]

Hi,

Any Replys ?????

Regards

Giri

[aashish_sinha]

You Did the right thing in communication channel that u selected the IS.

Hi

Just check out if you sending the correct parameters and also check out the payload you sending and check out in SXMB_MONI for you message that after success wat is the payload and match with your input.

Rather, for input check, In IR, get the XML data from ur Message Mapping and then save it to your inbox that is input directory.

Also check out the permission of Output directory and also check the configuration of sender and reciver communication channel.

Regards

Aashish Sinha

PS : reward points if helpful

[Former Member]

hi,

can you check in Receiver Communication Channel:

<b>Adapter engine : Integration Engine</b>

if it not Integration engine so plz make it <b>Integration Engine</b>

hope this will help

regards

HONEY

[Former Member]

Hi,

It Should be Integration Server in CC of the ID For Adapter Engine.

We have the Business System With the Role of Integration Server.

Should we need to change it to Application Server ??

In SXMB_ADM We did the Configuration of the Integration Server Also.

Please Let me Know.If Any thing to do

Regards

Giri

[Former Member]

Dear Seshagiri,

you first check your receiver communication channel processing mode.

Is is "do not created message" by mistake.

then change it.

2> Check the permission of that folder of target directory.

Allow full permission (777)

***PS: Reward points if useful

Regards,

Sumit Gupta

[Shabarish_Nair]

<i>Also chked with the comm. channel of sender and receiver, where the sender shows the message process details but not the receiver comm. channel.</i>

>>>

check the log of the CC for the reciever file adapter. what does it say?

also go to http://<yourserver>:<yourport5XXXX>/mdt/index.jsp and look into the trace.

[Former Member]

Hi Shabarish,

Thank you for your Reply.

I am Not Able to see Any Logs in http://<yourserver>:<yourport5XXXX>/mdt/index.jsp.

But I am Able to see Receiver Communication Channel Without Errors.

What Could be the Problem for <b>Not Viewing the Pipeline Steps in MONI</b>

Regards

Giri

[Shabarish_Nair]

<i>But Able to Se the Success Message With the Inbound Payload only.</i>

>>

in this case you sud see the messages in http://<yourserver>:<yourport5XXXX>/mdt/index.jsp (MDT) also.

i think its the problem with your receiver CC configuration. Can you check again on tht?

[Former Member]

check the status of the File Sender Adapter in the COmmunication channel.

If File Adapter (Sender) succsessfully sent the file to IS. then there should no be

any error.

Try to give the proper time stamp in SXMB_MONI.

If everything is ok at the Sender File adapter then message as to come in IS for processing:)

Check the Trace level from SXMB_ADM-->Integration Engine Configuration

Increas the Trace Level there.

Thanks

Farooq.