STMS configuration Activation error

[Former Member]

I just did client copy, and trying to configure this single system. After I set the rout, and try to distribute and activate it, It gives me program error

Error analysis

An exception occurred. This exception is dealt with in more detail below

. The exception, which is assigned to the class 'CX_SY_OPEN_SQL_DB', was

neither

caught nor passed along using a RAISING clause, in the procedure

"TRINT_CLEAR_FOR_DBCOPY" "(FUNCTION)"

.

Since the caller of the procedure could not have expected this exception

to occur, the running program was terminated.

Also, at check transport tool, it shows DB connect error: Error:SAP-System not installed properly. Error: EXIT(16)

tp returncode summary:

TOOLS: Highest return code of single steps was: 16

ERRORS: Highest tp internal error was: 0233

Output from tools called by tp:

Please help on this one. Thanks a lot.

Amy

[former_member618758]

Hi,

I would need more information about this.

Can you paste the related SLOG message to the error? In DIR_TRANS/log.

Thanks,

George

[Former Member]

Here is the content of the file. Thanks.

START EXPORT PREPARATION SB1 e 20070925170031 AMAO reuben

START tp_getprots SB1 E 20070925170031 AMAO reuben

STOP tp_getprots SB1 E 20070925170041 AMAO reuben

STOP EXPORT PREPARATION SB1 e 20070925170041 AMAO reuben

START EXPORT PREPARATION SB1 e 20070925170545 AMAO reuben

START tp_getprots SB1 E 20070925170545 AMAO reuben

STOP tp_getprots SB1 E 20070925170555 AMAO reuben

STOP EXPORT PREPARATION SB1 e 20070925170555 AMAO reuben

HALT 20070927141002

ERROR: SAP-System not installed properly. Systems name (SB1) is different from name in TADIR (AP1)

ERROR: EXIT(16) -> process ID is: 1339486

HALT 20070927141002

ERROR: SAP-System not installed properly. Systems name (SB1) is different from name in TADIR (AP1)

ERROR: EXIT(16) -> process ID is: 1425590

HALT 20070927142625

ERROR: SAP-System not installed properly. Systems name (SB1) is different from name in TADIR (AP1)

ERROR: EXIT(16) -> process ID is: 1450052

HALT 20070927142625

ERROR: SAP-System not installed properly. Systems name (SB1) is different from name in TADIR (AP1)

ERROR: EXIT(16) -> process ID is: 1339582

HALT 20070927150158

ERROR: SAP-System not installed properly. Systems name (SB1) is different from name in TADIR (AP1)

ERROR: EXIT(16) -> process ID is: 1437916

HALT 20070927150158

ERROR: SAP-System not installed properly. Systems name (SB1) is different from name in TADIR (AP1)

ERROR: EXIT(16) -> process ID is: 1376366

HALT 20070927150315

ERROR: SAP-System not installed properly. Systems name (SB1) is different from name in TADIR (AP1)

ERROR: EXIT(16) -> process ID is: 1327126

HALT 20070927150315

ERROR: SAP-System not installed properly. Systems name (SB1) is different from name in TADIR (AP1)

ERROR: EXIT(16) -> process ID is: 1294584

HALT 20070927163616

ERROR: SAP-System not installed properly. Systems name (SB1) is different from name in TADIR (AP1)

ERROR: EXIT(16) -> process ID is: 1413342

ERROR: Connect to SB1 failed (20070927164237, probably wrong environment).

ERROR: Connect to SB1 failed (20070927164554, probably wrong environment).

[former_member618758]

Hi again,

Thanks for the SLOG, I think I know what might happend. After the client copy, have you done the post

processing steps in SE06? If you have not, please go to SE06 to do

the post process steps. After that, please test again to see if the

problem still exists.

Thanks,

George

[Former Member]

Hi George,

SE06 is needed after system copy and not after client copy,

Hi Amy,

but anways George may have a point here. Did you do system copy or client copy Also what system do SB1 and AP1 represent.

Regards.

Ruchit

[Former Member]

Thanks for you input. Actually the error happened when I was trying to run from SE06. However, I found out the reason. I didn't create the temp file. Once I created it, this problem's been solved.

However, I have another problem now.

I am trying to do the client copy, so, I go to SCC4 to create new client. However, there's no proper logical system there for me to pick up. So, I go to BD54 to create the logical system. The problem is that it's keep giving me error "Changes to Repository or cross-client Customizing are not permitted". However, at SCC4, I've already set the client role as "customizing", and every setting as allow change and no restriction.

Any idea why this is happening, and how to solve this problem? Thanks a lot.

Amy

[former_member618758]

check SE06->system change option.

Thanks,

George

[Former Member]

George,

Thanks a lot for your suggession. We have this problem solved. We found that once we refresh our user buffer, there's no problem add new logical system. Thank you for your help.

Amy

[former_member618758]

Hi Amy,

Glad to know this problem is solved, great to know sdn is working as designed, lastly, please knidly award points to encourage people to help.

Thanks,

George