cancel
Showing results for 
Search instead for 
Did you mean: 

Transaction Code to VIEW the IDOC's in XI

Former Member
0 Kudos

Hi Guys,

I had configured the Partner Profile in R/3 and triggered the IDOC's to XI. I havent configured the scenario in IR or ID yet. Since i had triggered the IDOC's from R/3 and they show successful,which transaction should i use in XI to check whether the IDOC's had reached the XI system Succesfully or not.

Thanks,

KC.

Accepted Solutions (1)

Accepted Solutions (1)

Former Member
0 Kudos

try idx5

Florin

Answers (5)

Answers (5)

Former Member
0 Kudos

Hey

>>whether the IDOC's had reached the XI system Succesfully or not.

it will be better if u do the whole scenario and then test it via WE19,please don't test the scenario in parts specially when u have done nothing in IR or ID.

IDOC from R/3 will be send directly to the IE of XI but there it will fail coz u have nothing designed in XI which will handle that IDOC.

only thing u need to check is the connection between R/3 and XI which you have to do in SM59.no need to test IDOC after partner profile.

Thanx

Aamir

Former Member
0 Kudos

Hi

If you just want to see whether everything is right from the sender side, use can use IDX5 in XI.Outbound message shall be green if all is fine from the ALE Configurations.

If your doubt is solved kindly close the thread.

Thanks

Former Member
0 Kudos

Kittu,

Go to IDX5 if you are on NW2004s, PI system. There is a idoc monitor here.

This is valid also in XI 3.0 but I dont think it is fully functional here.

reg

Former Member
0 Kudos

Hi Kittu,

If you want to see the idocs in XI....use transaction SXMB_MONI and set filter criteria under "Sender -- Interface Name" : Select your message type-idoc type. For eg. MATMAS.MATMAS05...this will show you all message received in XI with your message/idoc type.

Nilesh

prasanthi_chavala
Active Contributor
0 Kudos

Hi Kittu,

Check in idx5 or sxmb_moni for the idoc message.

>><i> I havent configured the scenario in IR or ID yet.</i>

Since u have not done with design and configuration part..you will see error message in the sxmb_moni saying tat receiver could not be determined.

Regards,

Prasanthi.

Former Member
0 Kudos

Hi Kittu

Have a look at this blog, it has all TCodes.

/people/morten.wittrock/blog/2006/03/23/getting-started-with-xi-part-1-xi-30-cheat-sheet

Here it goes~

SXMB_IFR-- launch integration builder/ Repository/configuration/SLD ( XI HomePage)

Proxy Generation

SPROXY--Proxy generation

Monitering features:

SXMB_MONI-- monitering of messages

SXI_MONITOR - monitoring Processed Messages

SXMB_MONI_BPE--Business process monitering

Alerts:

ALRTCATDEF- To configure Alert Category

Adminsitration of XI

sxmb_adm-- Administration

QUEUE MONITORING

SMQ1 Outbound queue

SMQ2 Inbound Queue

IDoc's& RFC's related

IDX1- Port Configuration

IDX2 - for IDoc meta data

SM58--RFC error Log

SM59 - RFC Destination

IDX5 - Idoc Monitor

Others

SWELS---Event trace switching on and off.

SXI_MAPPING_TEST To test mappings

SXI_CACHE To check directory cache

To get the cache information For Adapters- go to SXI_CACHE

Hope this helps

Thanks

Abhishek