SM59 - RFC Destination Creation -- Error

[Former Member]

Hi Friends ,

<b> If i want to use RFC Sender Adpater i need to create destination for RFC right ?</b>

So, i have followed the Michal's blog

/people/michal.krawczyk2/blog/2005/03/29/configuring-the-sender-rfc-adapter--step-by-step

I have got the following error .

<b>Logon Connection Error</b>

Error Details Error when opening an RFC connection

Error Details ERROR: program rfcdestsamp not registered

Error Details LOCATION: SAP-Gateway on host ourhost / sapgw00

Error Details <b>DETAIL: TP rfcdestsamp not registered</b>

Error Details COMPONENT: SAP-Gateway

Error Details COUNTER: 36977

Error Details MODULE: gwr3cpic.c

Error Details LINE: 1694

Error Details RETURN CODE: 679

Error Details SUBRC: 0

Error Details RELEASE: 700

Error Details TIME: Wed Aug 29 14:57:48 2007

Error Details VERSION: 2

What other configuration i have to do ?

Do we need to go th R3 side SM59 ( to create the RFC Destination ?)

Please clarify this !

Regards.,

Shyam

[nisarkhan_n · Accepted solution]

Yes you have to create the RFC destination of type T in R/3

Create the RFC destination of type T

host: ourhost

service:sapgw00

and also your RFC sender CC should be active.

[Former Member · Accepted solution]

HI ,

First i need to create CC ?

[prasanthi_chavala · Accepted solution]

Hi Shyam,

First create RFC destination in SM59 and then create CC and give those details in the com channel.

Regards,

Prasanthi.

[Former Member · Accepted solution]

HI,

Do we need to create anything on R3 system ? With out connection test can i use in CC?

[nisarkhan_n · Accepted solution]

jsut run the Connection test to make sure it is fine, the host and gateway mentioned should be fine.

if the RFC dest is fine then the PID which you have mentnoined in RFC dest will be available for XI RFC sender adapter.

[prasanthi_chavala · Accepted solution]

Hi Shyam,

As pointed by kumar, please do a connection test once u create a RFC destination of type 'T'. Then create the RFC channel in the directory. Then give the other details. Make sure that in the gateway host and gateway service enter the values of your R/3 system.

Thanks,

Prasanthi.

[Former Member · Accepted solution]

Hi prasanthi,

As kumar specified the Connection test but am still getting the same error !

<i>Then give the other details. Make sure that in the gateway host and gateway service enter the values of your R/3 system.</i>

gateway host and gateway service are properly entered !

Type as T selected !

Regards.,

Shyam

Message was edited by:

shyam s

[nisarkhan_n · Accepted solution]

IS your Sender RFC adapter contains the same PID and is it active with Sender agrement?

i hope you have menioned the details in RFC destination

host: ourhost

service:sapgw00

[Former Member · Accepted solution]

Hi Shyam,

Ask your Basis guys to look into this.

Regards,

Kumar

[nisarkhan_n · Accepted solution]

Also, Can you list out the steps you have done till now.

[Former Member]

hi shyam,

after executing step 1 i.e creating porgram id at R/3 through XI.

got to ST22 at R/3 and check whether any dump is found against "XI creating porgram-id at R/3 level".

we failed at creating PROGRAM-ID itself at R/3 level because of missing authorizations against my R/3 user id,which we will be using at XI RFC channel.

generally problem will be at PROGRAM-ID creation itself,so just go to ST22 and check any authorizations missing for your userid which is being used at RFC channel configuring at XI.

Regards,

Rama Krishna

[Former Member]

hi shyam,

are you still facing problem in creating tcp/ip CONNECTION.

Regards,

Rama Krishna

[Former Member]

Also after activating the RFC sender CC, go to comm channel monitoring and check is there any error in that. Might possible your sender RFC CC is having error. If it is in green then go and do the connectivity testing.

-Gouri

Award points if helpful.:)

[Former Member]

Hi shyam,

create a RFC SENDER first and then activate the channel.

now go to sm59 there use the same program-id as u did at RFC SENDER COMMUNICATION CHANNEL.

note:program-id is registered by XI at R/3 level with details related to it's profile(XI profile).

step 1) create RFC COMMUNICATION CHANNEL with program-id as "any name" at XI first .

2)create TCP/IP connection with registered program-id created by XI at first step

so when you execute steps 2 then 1 you will get error ,coz by that time program-id is not yet registere by XI in R/3 domain.

Regards,

Rama Krishna

[Former Member]

Hi,

The programID which you are using in the RFC adapter should be the same as the one which was mentioned in the RFC destination.

Regards,

Kumar.

**Rewrad Points if helpful!!!!

[Former Member]

Hi kumar,

Thanks for ur reply. I am little bit confused here .

First i have to create RFC Sender adapter then in SM59 i need to configure ?

Please tell me the steps

Regards.,

Shyam

[Former Member]

Hi,

Create the RFC destiantion in SM59 as per Michal's Blog first and use the same program ID in your RFC Adapter.

Regards,

Kumar.

• Reward points if helpful!!!

[Former Member]

hI KUMAR,

I have done as same in michal's blog, Without connection test i have to create CC? and specify the Prog ID ?

[nisarkhan_n]

Shyam,

Create the RFC destination in R/3 according to the blog, make the note of the PID which you are mentioning in the RFC destination.

Create the RFC sender agrement and in the PID tab, mention the same PID which you given in RFC dest.

Only thing is your RFC Sndr Should also be active. then you can send the data from R/3 to XI.

[Former Member]

Hi,

Do a connection test as well...as your connection needs to be alive...

Then create your Comm..Channel..

Regards,

Kumar

[Former Member]

Hi kumar,

But in connection test i got the above error ! Then how can i proceed ? Some program id registration probelm !