Settings in SAP R/3 And XI While IDOC is Receiver

[Former Member]

Hi All,

If IDOC is the Sender Means, we need to Configure the Following

<b>In R/3</b>

1) Create Logical Sys of XI in R/3

2) Create RFC Destination in R/3 Towards XI ( RFC Dest Name Shld be Logical

System of XI )

3) Create Port ( WE21)

4) Create Partner Profile ( WE20 )

<b>In XI</b>

1) Create Logical Sys of R/3 in XI

2) Create RFC Destination in XI Towards R/3 ( RFC Dest Name Shld be Logical

System of R/3 )

3) Create Port ( IDX1)

4) Import Metadata ( IDX2 )

Here My Question is

If the IDOC is the Receiver Means Should we Configure All the Mentioned Above

OR

We have to Skip Some Configurations

Regards

Vamsi

Message was edited by:

Vamsi Krishna

[Former Member · Accepted solution]

hi,

yes vamsi ...u have to do the same settings...

[Former Member · Accepted solution]

Hi,

Should We Maintain the SAP R/3 Port Also, If IDOC is the Receiver Means

Or

No Need to Maintain

Regards

Vamsi

[Former Member · Accepted solution]

yes u have to maintain R/3 Port in XI if IDOC is receiver also.

[Former Member · Accepted solution]

Hi Sridhar,

According to your Ans

We need to maintain the Settings if IDOC is the Receiver That What we Maintained in the case of Sender IDOC.

Is it Right ???

Regards

Vamsi

[Former Member · Accepted solution]

Vamsee,

Base on the scenario you need to configure...

1. R3 --> XI..

In this case you will create RFC PORT / RFC destination on R3 system which wull point towards XI system. So you have to maintained Logical sysem and partner profile at R3 end.

You do not need to creat port on XI system in this case.

2.XI --> R3.

In this case you will create RFC PORT ( TC :IDX1) on XI and need to upload Metadata of same idoc( TC: IDX2) and RFC Destination on XI which will point towards R3 system.

Let me know if you need more details.

Nilesh

[Former Member · Accepted solution]

You have to create a RFC detination (Run SM 59 Tx) in R/3 not in XI.

XIer

[Former Member · Accepted solution]

when IDOC si receiver XI --> R/3

u create a RFC destination of type 3 in XI system poitning to the R/3 system and specify this RFC destination in the port that u create in IDX1

[Former Member]

Confusion. Please Let me Know What steps we need to do While IDOC is Receiver

See this

Message was edited by:

Vamsi Krishna

[Former Member]

Ans

[former_member614185]

Hi,

refer this blog,

/people/prateek.shah/blog/2005/06/08/introduction-to-idoc-xi-file-scenario-and-complete-walk-through-for-starters

[Former Member]

Hi

Ref

1. In SM 59 , you will have to create an RFC destination for the R3 system to which you are trying to post an IDOC to.

2. In IDX1, create the port to send the data

3. In IDX2, import the IDOC metadata.

In R3, in We20, create the partner profile with an entry for the inbound idoc in the corresponding logical system.

https://websmp201.sap-ag.de/nw-howtoguides

for IDX1- http://help.sap.com/saphelp_nw2004s/helpdata/en/3b/beb13b00ae793be10000000a11402f/frameset.htm

for IDX2-

http://help.sap.com/saphelp_nw2004s/helpdata/en/8a/b8b13bb3ace769e10000000a11402f/frameset.htm

http://help.sap.com/saphelp_nw04/helpdata/en/b9/c5b13bbeb0cb37e10000000a11402f/frameset.htm

Thanks

[Former Member]

Hi,

for receiever we need to do the following..

In R/3

1) Maintain of XI in R/3

2.) Create Partner Profile ( WE20 )

In XI

1) Create Logical Sys of R/3 in XI

2) Create RFC Destination in XI Towards R/3 ( RFC Dest Name Shld be Logical

System of R/3 )

3) Create Port ( IDX1)

4) Import Metadata ( IDX2 )

vasanth.