hi

[Former Member]

hi

what is rouding profile in (sale organization 1 ) of mater master data

[Former Member · Accepted solution]

Rounding Profile

Key that the system uses to adjust the order proposal quantity to

deliverable units.

Procedure

In Customizing, enter a threshold value from which the system should

round up to the next value per deliverable unit:

o If the requirements value exceeds the first threshold value, the

system always rounds up to the next multiple of the level found

o If the requirements value falls below the first threshold value, the

system copies the original requirements value.

Two other types of rounding exist:

o Dynamic rounding profile:

These profiles are used to round up quantities to logistical units

of measure (for example, layers). The contents of a logistical unit

of measure does not have to be know when creating the rounding

profile. It is determined by the master data from the material

master.

o Rounding profile with quantity to be added/subtracted

With these profiles, the given quantity is changed either by adding

a percentage or subtracting a percentage.

Only static rounding profiles are taken into account in requirements

planning. Neither dynamic rounding profiles not quantity addition/

subtraction are taken into account.

Examples

A material's base unit of measure is 1 unit; the purchase order is to be

delivered in layers (1 layer corresponds to 5 units) or in pallets (1

pallet corresponds to 8 layers which contains 40 units).

You maintain the profile as follows:

From a requirements of 2 units, the system is to round up to 5; from a

requirement of 32 units, the system is to round up to 40.

This results in the following order proposal quantities:

Requirement from 1 -> 1 requirement from 31 -> 30

Requirement from 2 -> 5 requirement from 32 -> 40

Requirement from 6 -> 10 requirement from 74 -> 80

Requirement from 7 -> 10

Dependencies

If no rounding profile has been entered, the system uses the rounding

value entered in the material master record for the planning run.

Regards,

Rajesh Banka

[Former Member]

Rounding profile is the Key that the system uses to adjust the order proposal quantity to deliverable units.

In Customizing, enter a threshold value from which the system should round up to the next value per deliverable unit:

If the requirements value exceeds the first threshold value, the system always rounds up to the next multiple of the level found

If the requirements value falls below the first threshold value, the system copies the original requirements value.

Two other types of rounding exist:

Dynamic rounding profile:

These profiles are used to round up quantities to logistical units of measure (for example, layers). The contents of a logistical unit of measure does not have to be know when creating the rounding profile. It is determined by the master data from the material master.

Rounding profile with quantity to be added/subtracted

With these profiles, the given quantity is changed either by adding a percentage or subtracting a percentage.

Only static rounding profiles are taken into account in requirements planning. Neither dynamic rounding profiles not quantity addition/ subtraction are taken into account.

[Former Member]

Rounding profiles for adjusting units of measure to match delivery or transport units

Rounding profiles can be maintained on a general or plant-specific basis. General maintenance is recommended as this requires you to enter less data.

EXP Customer places order of 8 units if rounding profile is activated system well round the quintity to 10 insted of 8

[Former Member]

• How to give points: Mark your thread as a question while creating it. In the answers you get, you can assign the points by clicking on the stars to the left. You also get a point yourself for rewarding (one per thread).

[Former Member]

Hii Shivaji,

This rounding profile key in Sales Org1 view of MM specifies the key which the system uses to adjust the order proposal quantity to the nearest deliverable units. Let us take the example of Cold drinks which you can deliver in cases i.e each case has 24 bottles. Now if you order more than 24 and less than

48, depending on the rounding profile we maintan the system will automatically adjust your order quantity to 24 or 48. I believe my answer will solve your doubt.

Please award maximum points!!.

Thanks,

Jay