cancel
Showing results for 
Search instead for 
Did you mean: 

Project stock in Inventory

former_member307772
Participant
0 Kudos

Hello experts,

Here my scenario is i have created a PO with account assignment "P" -WBS , the material i have taken ABC with material type with Quantity and value update ticked on at Plant level .Now when i post MIGO , system is not showing storage location hence system is unable to take that Material into inventory.

But when i have tried by keeping all other details as it is except the Material  XYZ (Which is made up of Material type with Quantity indicator ticked on not value at plant level), then system is showing storage location at MIGO.

Is there any specific reason for system is behaving like this? do we have any SAP notes ?

Please suggest

Accepted Solutions (0)

Answers (7)

Answers (7)

kenmelching
Active Contributor
0 Kudos

Account Assignment P is used for direct consumption (Non-Valuated Project Stock).

Look in your Project Definition and see what inventory you have selected, Valuated or Non-Valuated.

With Valuated Project Stock you will use Account Assignment Q.

Both of these should have Quantity Updating.  Valuated Project tock will have Value Updating.

former_member307772
Participant
0 Kudos

Hello Melching,

Thanks for your answer

But my doubt is when i run scenario where

Material with Material type (Value +Qty update ON) when posted for MIGO again account assignment " P" , but without QM activated , here system is showing storage location to take that material into Inventory

But Material with same material type i.e (Value + Qty update ON) when posted for MIGO against account assignment "P" but with QM activation , here system is unable to show storage location to take that material into Inventory.

So my assumption is whenever quality managed material is there against P , system is unable to post the same in Inventory.

Is this because , "P" and " Q quality " same time?

kenmelching
Active Contributor

First question, on the Project Definition what inventory indicator have you selected, Valuated Stock, Non-Valuated Stock, or No Stock?

For the Account Assignment on the PO there are 2 choices for using WBS Stock Segment, P or Q.  Which one you use is dependent on the stock indicator on the Proj Def.

Then when you are receiving material you can GR it into Unrestricted or Quality Stock.  This Q stock is not the same thing as the Q Account Assignment indicator.

joydeep_mukherjee2
Active Participant
0 Kudos

See your WBS settings there are the settings .

Joydeep

joydeep_mukherjee2
Active Participant
0 Kudos

Stock or non stock

joydeep_mukherjee2
Active Participant
0 Kudos

Check in Control Tab

former_member307772
Participant
0 Kudos

Its still showing the same , no effect.Please suggest further

Mrinal_K_Roy
Active Contributor
0 Kudos

Hi,

Suggest to check the checkbox for 'Project stock' under control tab of project definition flagged as 'Valuated' or not.

Regards,

Mrinal

sanjeevc
Active Contributor
0 Kudos

Hi,

just i have tested the same so issue is from purchase order as you have entered storage location into the PO so when you are going to MIGO it is asking storage location.

Regards,

Sanjeev

former_member307772
Participant
0 Kudos

Does anyone successfully take Project (P- account assignment category in PO) material -QM  Activated ) into Inventory ?

former_member307772
Participant
0 Kudos

Yes the storage location is maintained for Material master

joydeep_mukherjee2
Active Participant
0 Kudos

Please remove it and test in Dev client .

joydeep_mukherjee2
Active Participant
0 Kudos

Dear Sir ;

Please check the MM03 MRP view wheatherSloc for External Procurement is maintained or not 

sanjeevc
Active Contributor
0 Kudos

Hello,

Can you please check storage location in material master by MM03 if you have some value over there then it should ask storage location during MIGO.

Regards,

Sanjeev

joydeep_mukherjee2
Active Participant
0 Kudos

Dear sir ;

This is a standard behavior .If u tick Qty Update then it will ask for Sloc.

Joydeep

former_member307772
Participant
0 Kudos

But the main concern is when i ticked both Quantity and Value indicator On then why system is not asking storage location?

joydeep_mukherjee2
Active Participant
0 Kudos

As you are using WBS as a Acc. Assignment object system will consume as soon as there is a good receipt system will  not ask for Sloc .This is standard no need to worry .

Regards;

Joydeep

former_member307772
Participant
0 Kudos

Hi Joydeep,

But my concern is

Case 1 - Where i created PO with Material ABC with account assignment P - here ABC with material type having Quantity & Value update indicator ON - While doing MIGO storage location is not getting

Case 2 - Where i have created PO with Material XYZ with account assignment P - here XYZ with material type having Only Quantity indicator ON  -While doing MIGO storage location is getting

Now in both the cases , i have procuring the material for "P" ,but system is showing different behavior .