cancel
Showing results for 
Search instead for 
Did you mean: 

Checks after phase MAIN_SHDRUN/ACT_UPG were negative!

Former Member
0 Kudos

Hello All.

ERP upgrade stop with memory problem. I have this  part of logfile:

Termination occurred in the ABAP program "SAPLSDS1" - in "SETRANGE".

The main program was "RADMASG0_C3 ".

Thanks

Accepted Solutions (1)

Accepted Solutions (1)

Reagan
Advisor
Advisor
0 Kudos

I am not sure whether this will help but try to implement these:

***ERROR: Size of shared memory pool 10 too small

================================================================

SOLUTIONS: (1) Locate shared memory segments outside of pool 10

               with parameters like: ipc/shm_psize_<key> =0

SOLUTION: Increase size of shared memory pool 10

          with parameter: ipc/shm_psize_10 =128000000

***ERROR: Size of shared memory pool 40 too small

================================================================

SOLUTIONS: (1) Locate shared memory segments outside of pool 40

               with parameters like: ipc/shm_psize_<key> =0

SOLUTION: Increase size of shared memory pool 40

          with parameter: ipc/shm_psize_40 =112000000

Shared memory disposition overview

Regards

RB

Former Member
0 Kudos

Hi

I have this value i profile file:

#ipc/shm_psize_10 = 40000000

ipc/shm_psize_10 = 128000000

# *** CHANGE for the shadow instance ***

#ipc/shm_psize_40 = 68000000

ipc/shm_psize_40 = 112000000

abap/heap_area_dia = 10000000000

I donot know why I get this 2 error when i run sappfpar check pf=R3U_DVEBMGS08_SAPUX1.

Should I increas this to parameter Again?

Thanks

Reagan
Advisor
Advisor
0 Kudos

You may change the values as suggested in the output and restart the system.

Secondly check PAM and make sure that the version of HP-UX is supported for EHP6.

Regards

RB

Former Member
0 Kudos

Hi,

We had 64 GB memmory.

At last I could continue   find out  . When there is less than 128 GB memory in server the parameres value should be:

abap/heap_area_dia = 8000000000

abap/heap_area_nondia = 8000000000

abap/heap_area_total = 8000000000

Thanks

Reagan
Advisor
Advisor
0 Kudos

WOW. 8 GB of heap.

Good to know that you could continue

Good Luck

RB

Former Member
0 Kudos

Hi Reagan.

I have this line from /abap/tmp/SAPA702EPU

I can see some line in the SAPA702EPU fil:

I donot think there is any error.

Any idea what is mean? 

.

.

EDO533X*** Activate objects at level "150"

3 EDO639 Too low cost ("1.800") for parallel processing. Minimum: "6.000"

3 EDO634 * Synchronous execution, no parallel processing *

3 EDO680XSynchronous processing: "0" sec., "2" objects, "1.800" costs

1 EDO533X*** Activate objects at level "151"

3 EDO639 Too low cost ("1.050") for parallel processing. Minimum: "6.000"

3 EDO634 * Synchronous execution, no parallel processing *

3 EDO680XSynchronous processing: "0" sec., "1" objects, "1.050" costs

.

.

.

Thanks

Reza

Reagan
Advisor
Advisor
0 Kudos

What is the status in the SUM tool ?

They are not errors

Regards

RB

Former Member
0 Kudos

Hi,

I don't see any error .These are just stats to activate the object and to do it in parallel

Thanks

Rishi abrol

Former Member
0 Kudos

Hi,

Good.

Thanks

Former Member
0 Kudos

What du you mean with.

The status in the SUM tool ?

I am still in ACT_UPG.

Thanks

Reagan
Advisor
Advisor
0 Kudos

The ACT_UPG phase is one of the longest phases in the upgrade process.

As long as there is no errors reported in the SUM tool you may wait until it finishes.

You may check the progress with the logs in the /SUM_Directory/abap/tmp directory.

Once a task is completed the logs are moved to the /SUM_Directory/abap/log directory

Regards

RB

Former Member
0 Kudos

Hi I have this error:

3 EDO548XActivate dependent search help "H_AT30"
   1EEDH164 Types of search help param. "XFORMEL" and field of selection method incompatible
   3 EDH109 Search help "H_AT30" was not activated
1EEDO519 "Srch Help" "H_AT30" could not be activated

   3 EDO548XActivate dependent search help "H_PAD_CN_PASSRULE"
   1EEDH164 Types of search help param. "ERRAT" and field of selection method incompatible
   3 EDH109 Search help "H_PAD_CN_PASSRULE" was not activated
1EEDO519 "Srch Help" "H_PAD_CN_PASSRULE" could not be activated

   3 EDO548XActivate dependent search help "H_T5EAE"
   1EEDH164 Types of search help param. "ATEXT" and field of selection method incompatible
   3 EDH109 Search help "H_T5EAE" was not activated

I think I should choos:

Accept non-severe errors and repeat phase MAIN_SHDRUN/ACT_UPG and continue.

Thanks

Former Member
0 Kudos

Hi,

Please check the below note.

Note 1456978 - Search help can not be activated during upgrade or EHPI

Thanks

Rishi Abrol

Former Member
0 Kudos

Ja correct Thanks

Reagan
Advisor
Advisor
0 Kudos

Just ignore and continue

Regards

RB

Former Member
0 Kudos

Hi,

I am at PRAS_AIMMRG phase I got this error.

I had create rfc connection in client 010 and 001  but did not helps.

Any advice? 

EPU126XPost-import methods for change/transport request: "SAPK731XPRA90000115"

4 EPU111    on the application server: "sapux1"

2 EPU122XPost-import method "FINB_TR_AFTER_IMP_METHOD" started for "FINB_LOCAL_CONTENT" "T", date and time: "20130928152542"

A2 EFINB_TR 096 Postprocessing of client cascade was skipped for client "000"

A2 EFINB_TR 097 Transport tool FINBASIS: Client cascade for client "001" started

A2EEFINB_TR 032 No suitable RFC destination could be found"001"

A2 EFINB_TR 098 Transport tool FINBASIS: Client cascade for client "001" finished

A2 EFINB_TR 097 Transport tool FINBASIS: Client cascade for client "010" started

A2EEFINB_TR 032 No suitable RFC destination could be found"010"

A2 EFINB_TR 098 Transport tool FINBASIS: Client cascade for client "010" finished

2EEPU133 Errors occurred during post-handling "FINB_TR_AFTER_IMP_METHOD" for "FINB_LOCAL_CONTENT" "T"

3 EPU135 "FINB_TR_AFTER_IMP_METHOD" belongs to package "FINB_TRANSPORT_TOOL"

2EEPU136 The errors affect the following components:

2EEPU137    "FIN-FB" ("Financials Basis")

Thanks

Former Member
0 Kudos

Hi,

Can you please share the log

XPRASUPG.ELG

Thanks

Rishi Abrol

Former Member
0 Kudos

Hi,

Thanks for reply.

Here log XPRASUPG.ELG file.

I think my solution is in Note 644610 note. The problem is have no user ddic in client 010.

Pleas see the added file.

Thanks

Former Member
0 Kudos

Hi,

Your note is part of this one..

Note 912369 - FINB_TR_DEST, after import failures, transport errors

Which came from

Note 1681434 - Upgrade SAP SEM 634 NW 730 to SAP SEM 736 NW 731

Additional information about the upgrade

  • Additional information about the prepare
    Phase IS_SELECT
    None of the add-on components mentioned above must occur in the phase IS_SELECT.
  • Phase BIND_PATCH
    Here, the system displays which Support Packages are located in the <DIR_EPS_ROOT>/in directory and can be included in the upgrade.
  • Phase XPRAS_AIMMRG
    In this phase, if a termination occurs with the following message: Errors occurred during post-handling "FINB_TR_AFTER_IMP_METHOD" for "FINB_LOCAL_CONTENT" "T"
    you must implement SAP Note 912369.

Thanks

Rishi Abrol

Former Member
0 Kudos

Hi,

Correcet Thanks. I have create a RFC connection for client 001. Becuase I have pasword for ddic user. But in clien 010 The user ddic is locek and I can not logon in clien 010  with my user becuase upgrade is runing. I treid to use a system user but didnot works.

Any idea how can I unlock this user in 010 client?

Thanks

Former Member
0 Kudos

Hi,

I have this

A2 EFINB_TR 033 Import carried out using RFC destination "FINBTR@R3UCLNT010"

A2AEFINB_TR 077 Error or termination in target client: "Navn eller password ikke korrekt (gentag logon)""010"

A2AEFINB_TR 078 Target client: "010" user: " " RFC dest.: "FINBTR@R3UCLNT010"

A2 EFINB_TR 098 Transport tool FINBASIS: Client cascade for client "010" finished

2EEPU133 Errors occurred during post-handling "FINB_TR_AFTER_IMP_METHOD" for "FINB_LOCAL_CONTENT" "T"

Is it possible solve this problem if I could login clien 010 and unlock the ddic user and use this user in RFC coonection?

should implement SAP Note 912369 in client main instance. But upgrade is runing?

Former Member
0 Kudos

Hi,

If you want to unlock the shadow instance then you may do this from the upgrade directory

SAPup unlockshd SID

Thanks

Rishi Abrol

Former Member
0 Kudos

Hi,

The shadow instance is not runing in this phase.

I need to login to client 010. for unloch ddic user. Is it possible to stop upgrade in this phase? Or this make more problems?

Former Member
0 Kudos

Hi ,

below is the process to lock and unlock.

What do you mean that the upgrade is still running.

Dint you get an error in the SUM tool.

To unlock the SAP system, enter the following commands (here <transport_profile> or DEFAULT.TPP is the transport profile of the transport domain to which the system is connected): The system may be either the original SAP system or the shadow system, depending on which one the error occurred.ıÄcBÍ

Original SAP systemcd /<update directory>/abap/exe

A Appendix

A.2 Troubleshooting

2012-11-26 CUSTOMER 173/214

./tp unlocksys <SAPSID> pf=../var/DEFAULT.TPP./tp unlock_eu <SAPSID> pf=../var/DEFAULT.TPPflŸ!Á£×

Shadow systemcd /<update directory>/abap/binSAPup unlockshd

2.

Log on to the SAP system or shadow system and correct the error.

3.

To lock the original SAP system or shadow system again, enter the following commands:flŸ!Á£×

Original SAP systemcd /<update directory>/abap/exe./tp lock_eu <SAPSID> pf=..\var\DEFAULT.TPP./tp locksys <SAPSID> pf=../var/DEFAULT.TPPflŸ!Á£×

Shadow systemcd /<update directory>/abap/binSAPup lockshd

Thanks

Rishi Abrol

Former Member
0 Kudos

Hi,

Sorry

I want to use ddic user for RFC connection fom  original SAP system client 000 to client 010.

But ddic user in clien 010 is locked.

So i can not login client 010 by dialog user to unlock ddic user I get this massage logon not possible upgrade still runing.

I think I should stop upgrdae and login client 010 and unlock ddic user and start upgrade again?

Thanks

Answers (11)

Answers (11)

Reagan
Advisor
Advisor
0 Kudos

Hello Reza

Is it possible solve this problem if I could login clien 010 and unlock the ddic user and use this user in RFC coonection?

should implement SAP Note 912369 in client main instance. But upgrade is runing?

You are in the downtime phase.

The kernel switch and the repository switch have been completed

Any action to be taken should be done on the main system.

You need to unlock the SAP system from the OS level using the tp tool.

tp unlocksys <SID> pf=<TP-Profile with path>

tp unlock_eu <SID> pf=<TP-Profile with path>

Regards

RB

Former Member
0 Kudos

Hi Reagan.

Thanks foralle your reply. At last I am finish with upgrade.

My problem was ddic user was look on client 010. I  did need this user for RFC connection from client 000 to client 010

I did reset sap* user in client 010 logon with that user and unlock the ddic user and my problem was solved.

Thanks again for good advice alle of you.

Reza

Former Member
0 Kudos

Pls use  SPDD and determine any correction require in the ABAP Dictionary objects with DDIC.

Former Member
0 Kudos

1641754 - EHP5:Persistency of SFW objects during mass act. causes dump

"

During EHP5 installation a dump occurs in phase MAIN_SHDRUN/ACT_UPG with runtime error SAPSQL_ARRAY_INSERT_DUPREC. Mass activation is restarted and memory optimization parameter is set.
Error can also occur when restarting the mass activation (RADMASG0_C3) when using parameter 'Full Persistence' (PERSIST)."

This may help you...

Thanks,

Prabhakar

Reagan
Advisor
Advisor
0 Kudos

Hello Reza

ztta/roll_extension = 64000000000

em/initial_size_MB = 15000

This is wrong.

The parameter ztta/roll_extension should be less than em/initial_size_MB

http://help.sap.com/saphelp_nw2004s/helpdata/en/02/9626b3538111d1891b0000e8322f96/content.htm

http://help.sap.com/saphelp_40b/helpdata/EN/02/9626e7538111d1891b0000e8322f96/content.htm

Change the value of ztta/roll_extension to 4000000000 and restart the system and retry.

Regards

RB

Former Member
0 Kudos

Hllo,

Reaga,

Thanks fo reply,

I did change tht parameter  ztta/roll_extension to 4000000000 too. But still the same.

Stop wit error.  SYSTEM_NO_TASK_STORAGE.

Thanks

Former Member
0 Kudos

Hi,

I think that you should push it hard back to sap.

That will help you solve the issue and your time 🙂

Thanks

Rishi

Former Member
0 Kudos

Hi,

I had create a mesage at SAP for 7 dag ago. My it-chef has call them too. But they don't reply.

Thanks

Reza

Former Member
0 Kudos

Hi,

I Still have the same problem:(

I have this profile parameter in shadow:

# *** CHANGE for the shadow instance ***

ipc/shm_psize_10 = 128000000

# *** CHANGE for the shadow instance ***

#ipc/shm_psize_40 = 68000000

ipc/shm_psize_40 = 112000000

abap/heap_area_dia = 10000000000

abap/heap_area_nondia = 10000000000

abap/heap_area_total = 10000000000

ztta/roll_extension = 4000000000

ztta/roll_area = 20000000

em/initial_size_MB = 15000

But I get this  2 error_When I run sappfpar check pf=R3U_DVEBMGS08_SAPUX1.

I have this  from shadow: sappfpar check pf=R3U_DVEBMGS08_SAPUX1

--------------------------------------------------------------------------------------------

sapux1:r3dadm 30> sappfpar check pf=R3U_DVEBMGS08_SAPUX1
sappfpar=>sapparam(2): fopenU("R3U_DVEBMGS08_SAPUX1","r"): No such file or direc                                                                                                                                tory
sappfpar=>No Profile used.
sappfpar=>sapparam: SAPSYSTEMNAME neither in Profile nor in Commandline


================================================================================
==   Checking profile:     <no_profile>
================================================================================


***ERROR: Size of shared memory pool 10 too small
================================================================
SOLUTIONS: (1) Locate shared memory segments outside of pool 10
               with parameters like: ipc/shm_psize_<key> =0

SOLUTION: Increase size of shared memory pool 10
          with parameter: ipc/shm_psize_10 =128000000

***ERROR: Size of shared memory pool 40 too small
================================================================
SOLUTIONS: (1) Locate shared memory segments outside of pool 40
               with parameters like: ipc/shm_psize_<key> =0

SOLUTION: Increase size of shared memory pool 40
          with parameter: ipc/shm_psize_40 =112000000

Shared memory disposition overview
================================================================
Shared memory pools
Key:   10  Pool
            Size configured.....:    19880000 (  19.0 MB)
            Size min. estimated.:   124203728 ( 118.4 MB)
            Advised Size........:   128000000 ( 122.1 MB)

Key:   40  Pool for database buffers
            Size configured.....:    14250000 (  13.6 MB)
            Size min. estimated.:   109175040 ( 104.1 MB)
            Advised Size........:   112000000 ( 106.8 MB)

Shared memories inside of pool 10
Key:       11  Size:      500000 (   0.5 MB) Factory calender buffer
Key:       12  Size:     6000000 (   5.7 MB) TemSe Char-Code convert Buf.
Key:       13  Size:    60500000 (  57.7 MB) Alert Area
Key:       14  Size:     4400000 (   4.2 MB) Presentation buffer
Key:       16  Size:       22400 (   0.0 MB) Semaphore activity monitoring
Key:       17  Size:     2780560 (   2.7 MB) Roll administration

Shared memories inside of pool 40
Key:       42  Size:     7232992 (   6.9 MB) DB TTAB buffer
Key:       43  Size:    32534392 (  31.0 MB) DB FTAB buffer
Key:       44  Size:     7958392 (   7.6 MB) DB IREC buffer
Key:       45  Size:     4886392 (   4.7 MB) DB short nametab buffer
Key:       46  Size:       20480 (   0.0 MB) DB sync table
Key:       47  Size:     3073024 (   2.9 MB) DB CUA buffer
Key:       48  Size:      500000 (   0.5 MB) Number range buffer
Key:       49  Size:     2968344 (   2.8 MB) Spool admin (SpoolWP+DiaWP)

Shared memories outside of pools
Key:        1  Size:        2500 (   0.0 MB) System administration
Key:        2  Size:     6211356 (   5.9 MB) Disp. administration tables
Key:        3  Size:    13714400 (  13.1 MB) Disp. communication areas
Key:        4  Size:      503248 (   0.5 MB) statistic area
Key:        6  Size:   319488000 ( 304.7 MB) ABAP program buffer
Key:        7  Size:       14838 (   0.0 MB) Update task administration
Key:        8  Size:    67108964 (  64.0 MB) Paging buffer
Key:        9  Size:   134217828 ( 128.0 MB) Roll buffer
Key:       18  Size:      917604 (   0.9 MB) Paging adminitration
Key:       19  Size:    30000000 (  28.6 MB) Table-buffer
Key:       30  Size:        3072 (   0.0 MB) Taskhandler runtime admin.
Key:       31  Size:     1806000 (   1.7 MB) Dispatcher request queue
Key:       33  Size:    10240000 (   9.8 MB) Table buffer, part.buffering
Key:       41  Size:    25010000 (  23.9 MB) DB statistics buffer
Key:       51  Size:     3200000 (   3.1 MB) Extended memory admin.
Key:       52  Size:       40000 (   0.0 MB) Message Server buffer
Key:       54  Size:     4202496 (   4.0 MB) Export/Import buffer
Key:       55  Size:        8192 (   0.0 MB) Spool local printer+joblist
Key:       57  Size:     1048576 (   1.0 MB) Profilparameter in shared mem
Key:       58  Size:        4096 (   0.0 MB) Enqueue ID for reset
Key:       62  Size:    85983232 (  82.0 MB) Memory pipes
Key:       63  Size:      409600 (   0.4 MB) ICMAN shared memory
Key:       64  Size:     4202496 (   4.0 MB) Online Text Repository Buf.
Key:       65  Size:     4202496 (   4.0 MB) Export/Import Shared Memory
Key:     1002  Size:      400000 (   0.4 MB) Performance monitoring V01.0
Key: 58900100  Size:        4096 (   0.0 MB) SCSA area

Nr of operating system shared memory segments: 28

Shared memory resource requirements estimated
================================================================
Total Nr of shared segments required.....:         28
System-imposed number of shared memories.:        512
Shared memory segment size required min..:  319488000 ( 304.7 MB)
System-imposed maximum segment size......: 1073741824 (1024.0 MB)

Swap space requirements estimated
================================================
Shared memory....................:  910.7 MB
..in pool 10   19.0 MB,  624% used !!
..in pool 40   13.6 MB,  766% used !!
..not in pool:  679.9 MB
Processes........................:   29.0 MB
Extended Memory .................: 4092.0 MB
------------------------------------------------
Total, minimum requirement.......: 5031.7 MB
Process local heaps, worst case..: 1907.3 MB
Total, worst case requirement....: 6939.0 MB

Errors detected..................:    2
Warnings detected................:    0

Any help?

Thanks

Reagan
Advisor
Advisor
0 Kudos

This is what I see

Error in libunwind: Out of memory. Try with a higher value for UNWIND_RESERVE_MEM (current val

Maybe this is rubbish.

Stop all the SAP system and then clean the shared memory segments. If possible reboot the machine.

Get an HP-UX specialist to check the parameter or environment variable UNWIND_RESERVE_MEM and set it to a higher value.

Or set it for the session for the r3uadm user

export UNWIND_RESERVE_MEM=10000

Start SAP main instance and the shadow instance.

Also make sure that the swap space settings for HP-UX are correctly done.

I strongly believe this is due to the OS level settings.

Review these SAP notes and make sure everything is set as advised.

Note 1112627 - SAP on HP-UX: Recommendations for swap and pseudo swap

Note 1075118 - SAP on HP-UX: FAQ

Note 172747 - SAP on HP-UX: OS kernel parameter recommendations

Regards

RB

Former Member
0 Kudos

Hi,

Thanks for reply.

I have done all this advice, But still I have the same problem.

I have only one aktive  installation in server with 64Gb memory. During ACT-UPG after 7 houres about 40Gb memory be used and upgrade stop with error.

I am using SUM version 8. Is it anybody has tried this situation?

Is it any bug in SUM version 8?

Any adviceshould I stop this upgrade and and use SUM version 7?

Thanks


former_member185239
Active Contributor
0 Kudos

Hi Reza,

is the job RDDMASGL ios getting failed?

can you please paste the job logs and error logs once again.

With Regards

Ashutosh Chaturvedi

Former Member
0 Kudos

Hi Ashutosh.

Yes  the job RDDMASGL ios getting failed.

Pleas see the added firl. I think there is some problem with SUM version 8.

Thanks

former_member185239
Active Contributor
0 Kudos

Hi Reza,

goto the shadow system kernel and Run the command

sappfpar check pf=<profile of the shadow system>

and then change the parameter as suggested.

http://help.sap.com/saphelp_nw2004s/helpdata/en/66/380fb7d43d11d188bd0000e83539c3/content.htm

With Regards

Ashutosh Chaturvedi

Former Member
0 Kudos

Hello,

We have problem with value of parameter or environment variable UNWIND_RESERVE_MEM.

Any idea where  can we set it to a higher value.

Thanks

Former Member
0 Kudos

Hi,

You can set it to using the below command.

export UNWIND_RESERVE_MEM=the value you want to set it to.

did SAP tell you to set this value. Did they tell to to set it permanently or for the time for the upgrade only.

You can also set in the file .sapenv_hostname.csh or sh depending on the shell in home/sidadm.

You might have to stop the SUM tools and the shadow instance . log off and relogin back again to sidadm.

Thanks

Rishi abrol

Former Member
0 Kudos

Hi,

Thanks for reply.

I have this from sap :

As an immediate action it is necessary to increase valur of HP-UX

parameter UNWIND_RESERVE_MEM from 16 ( current value ) to 64.

.

Thanks

Former Member
0 Kudos

Hi,

Ok . Please cross check with SAP that you need to remove the parameter after the upgrade is done.

Once you set it in the sapenv file you can logoff and when you login you should see it in the parameters when you run command

env

Thanks

Rishi Abrol

Former Member
0 Kudos

Hi,

We had done that. I restart upgrade. Hope this time Works.

Thanks Again for good advice.

Thanks

Reza

Reagan
Advisor
Advisor
0 Kudos

Hello Reza

Maybe this is rubbish.

Stop all the SAP system and then clean the shared memory segments. If possible reboot the machine.

Get an HP-UX specialist to check the parameter or environment variable UNWIND_RESERVE_MEM and set it to a higher value.

Or set it for the session for the r3uadm user

export UNWIND_RESERVE_MEM=10000

Start SAP main instance and the shadow instance.

Also make sure that the swap space settings for HP-UX are correctly done.

I strongly believe this is due to the OS level settings.

Looks like what I thought rubbish could be your savior.

Just follow the instructions I have mentioned here.

Good Luck

RB

Former Member
0 Kudos

Hello Reagan.

Yes that was correct. I had follow the instructions but the parameter UNWIND_RESERVE_MEM was set sa permanently. 

-export UNWIND_RESERVE_MEM=64.

Thanks

Reza

Former Member
0 Kudos

Hi.

Upgrade stop again with same error. Very strang.

Reagan
Advisor
Advisor
0 Kudos

Try to set the value I have given you.

Regards

RB

Former Member
0 Kudos

Hi Reagan,

you mean set it for the session for the r3uadm user ?

export UNWIND_RESERVE_MEM=10000

Thanks

former_member185239
Active Contributor
0 Kudos

Hi Reza,

If possible log on to Shadow system and check whether the  background job RDDMASGL is getting failed or not.

If it is getting failed you need to increase the below parameter

1. ztta/roll_area            (1.000.000 - 15.000.000)                                        

           Classic roll area per user and internal mode                                          

          usual amount of roll area per user and internal mode

2. ztta/roll_extension       (10.000.000 - 500.000.000)                                      

          Amount of memory per user in extended memory (EM) 

3. abap/heap_area_total      (100.000.000 - 1.500.000.000)                                   

         Amount of memory (malloc) for all users of an application background processes are running on one server, temporary bottlenecks may occur. Of course, the amount of memory (in bytes) must also be available on the machine (main memory or file system swap).                           

         

Caution:                                                                              

           The operating system must be set up so that there is also                             

            enough memory for each process. Usually, the maximum address                          

            space is too small.                                                                   

           Ask your hardware manufacturer or your competence center                              

          about this. In this case, consult your hardware vendor

4. abap/heap_area_dia:        (10.000.000 - 1.000.000.000)                                      

    Restriction of memory allocated to the heap with malloc                               

    for each dialog process.

5.  abap/heap_area_nondia:

6. em/initial_size_MB:

Note 44528 - STORAGE_PARAMETERS_WRONG_SET    

With Regards

Ashutosh Chaturvedi

Reagan
Advisor
Advisor
0 Kudos

Hello

I remember suggesting you about using a different version of the kernel. Have you tried that ?

Check whether the OS is configured according to this SAP Note

Note 172747 - SAP on HP-UX: OS kernel parameter recommendations

Make sure there is sufficient swap configured.

Connect to the SAP system and provide me the out for :

Tx SE38 - RSMEMORY

Regards

RB

Former Member
0 Kudos

Hello,

Yes I had tried  with a older kernel but the same.

Thanks for note yes I did check that too.

I am still waiting for sap reply.

We had contact sap for tow dag ago "note 1281633 - Speed Up Processing of a Customer Message" to time for speed up for this process.

Very strang they did not response.

The first AGS Primary Support from sap har told  message will now be routed to the component area responsible for RADMASG0_C3.

Program/report   RADMASG0_C3   No information found

Report cat.   No information found

History       SAP         /SAP         29.02.2012

Area      BC-DWB        ABAP Workbench

I waiting for any respons.

Her is resultof Tx SE38 - RSMEMORY:

Thanks

Former Member
0 Kudos

Hi Reagan,

Thanks for reply.

I had tried to use the older kernel but didnot help.

I had rewrite the existing kernel with the new one.

Should I just use new kernel without any rewrite the old one?

Thanks

Former Member
0 Kudos

Hi,

You can used the new kernel .

Thanks

Rishi abrol

Former Member
0 Kudos

Hi Rishi,

The kernel for shadow instance was createt by SUM? Is it ok to use another one?

Thanks

Former Member
0 Kudos

Yes Ejersbo.. It is normal to upgrade the kernel.

Former Member
0 Kudos

Hi,

I know befor upgrade we should ues the latest kernel.

I am in ACT-UPG phase during activation ABAP dictionary, is it ok to change the kernel that was createt by SUM in shadow instance

Thanks

Reagan
Advisor
Advisor
0 Kudos

Could you provide the configuration of the server where the EHP upgrade is done ?

Also are there any other applications running on this system apart from this SAP system ?

Additionally check the memory assigned for SAP and Database

Regards

RB

Former Member
0 Kudos

Hello,

There is one more sap installation running on this server. We have 64 gb memory, so this is not the problem.

I am very new on unix. let me see where I can get   configuration of the server.

Thanks

Former Member
0 Kudos

Hi mate,

Please tell me that did you get the ulimit thing fixed which was suggested to you earlier.

Try to set one parameters in the profile and let the system take it self.

So use Physical memory parameters.

PHYS_MEMSIZE

Note 88416 - Zero administration memory management for the ABAP server

If you think that no the above things cant fix the issue. Please raise message to sap.

Thanks

Rishi abrol

Former Member
0 Kudos

Hi man,

I had  raise message to sap, they not fund any problem with upgrade profile.

They talk about  component RADMASG0_C3 used a lot of memery.

The message was  routed to another area for some times.

I would like to know if someone had problem with component RADMASG0_C3?

Thanks 

Former Member
0 Kudos

Hi,

Please share more logs if still not fixed.

Thanks

Rishi abrol

Former Member
0 Kudos

Hi,

On last week I  had problem with ERP  EHP6 upgrade , upgrade was stop in ACT_UPG Phase.

I tried to reset that upgrade and start form scrach.

Now I am in the same situation upgrade stop with " SYSTEM_NO_TASK_STORAGE".

I have done this change  from note 1387739.

I had create a message for sap too. They saged  "The current memory parameters seem fine

as they are well beyond the default values recommended".

They talking about some problem with "Program/report   RADMASG0_C3   No information found".

The message was routed to the component area responsible for RADMASG0_C3.

The problem is SAP did not come back with any help and we have developer that waiting for this installation.

The only log file I had is from ST22.

I just tried to ask if somebody had problem with "component RADMASG0_C3"?

Thanks

ashish_vikas
Active Contributor
0 Kudos

you may also check this wiki document -

http://wiki.scn.sap.com/wiki/display/ERP6/How+to+improve+performance+in+ACT_UPG

best Regards

ashish

Reagan
Advisor
Advisor
0 Kudos
Former Member
0 Kudos

This is the activation of dictionary objects, retry at least twice and come back if the problem persists.

Cheers Michael