on 03-09-2007 9:06 AM
Hi Experts,
I'm not able to replicate the materials from R/3 to SRM,earlier i was successfull in performing this task,but after sometime there seems to be a problem,but when checked in the the transaction SMOHQUEUE ,system displays the message as Status of Queue Demon on Hold,even after releasing the queues still the same error being displayed,i've scheduled a job as per the note no 681516 but still the problem persists,please advice.
Thanks and Regards,
Sathya kumar.
Hi
What all error logs are coming in RZ20 and SLG1 Transactions in this case. ?
<u>Please refer to following OSS notes as well.</u>
<b>895863 Realignment queue in HOLD status for no apparent reason
970292 MIP implementation, source code corrections and corrections
453882 Parallel processing of the R&R queues
1014410 MIP Queue framework conversion: Migration of queue entries
480543 CRM MW R&R queues in status STARTING (no processing)
1001051 New queue framework: Queues do not exist
1012140 Extract during activation of 'Initially Inactive' sites
1011874 Generation error in the realignment service
1005561 Lock reset with resource bottlenecks in MIP queues
752584 SMOHQUEUE: Retry with technical errors when setting locks
794569 Short dump with detail display in SMOHQUEUE
762261 Addition to Note 638617 and 638628
655417 EXTRACT queue hangs with reference on ST22
624921 Activities after a system start (R/3 or CRM)</b>
Keep me posted.
Hope this will help.
Please reward suitable points, incase it suits your requirements.
Regards
- Atul
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Marcin/Atul,
I've checked the sap note no 305881,after setting up the RFC logical destination SAPCRM_MW_RR_000 with service user i'm not getting the error as "Error during aRFC (SAPCRM_MW_RR_000:Name or password is incorrect. Please re-enter" .Please advice to release the R&R queues.
Thanks and Regards,
Sathya kumar.
Hi
<u>In SM59 transaction, the user id of the RFC user must have following attributes -></u>
<b>The RFC user must have SAP_ALL and SAP_NEW authorizations. The username or Password should be configured in both the R/3 and SRM systems.
Note ->The user must exist in both the systems and must have the same password in bot the systems.</b>
Hope this will help.
Please reward suitable points, incase it suits your requirements.
Regards
- Atul
Hi
<u>Please ensure that the dependent OSS notes are configured properly.
Ask you BASIS person to help you out in this case.</u>
<b>Note 480543 - CRM MW R&R queues in status STARTING (no processing)
Note 459151 - Possible termination during data transfer with qRFC</b>
Hope this will help.
Please reward suitable points, incase it suits your requirements.
Regards
- Atul
Hi,
did you check RFc queues? (transaction SMQ1, SMQ2) ?
Regards,
Marcin
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Marcin,
What are the other areas i should look for to pull the materials,i have set the filter and then started initial load and checked in the both systems systems for queues which are clear and in the transaction R3AM1 all the requests DNL_CUST_BASIS3,DNL_CUST_PROD0,DNL_CUST_PROD1,DNL_CUST_SRVMAS are shown with o.k status green colour, not able to trace where the error occur, please advice.
Thanks and Regards,
Sathya kumar.
Hi Marcin,
In the transaction SMOHQUEUE when tried to start the Queue demon i'm getting following error :
"Starting Queue Demon not successful.
Error during aRFC (SAPCRM_MW_RR_000:RFC destination SAPCRM_MW_RR_000 does not exist.)"
Please advice on how to start the queue demon.
Thanks and Regards,
Sathya kumar.
User | Count |
---|---|
1 | |
1 | |
1 | |
1 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.