cancel
Showing results for 
Search instead for 
Did you mean: 

Single import\Mass import (STMS)

former_member226585
Participant
0 Kudos

Comrades, Trouble in the following.

I put the strategy of import - Single Import
In all systems relating to this landscape Mass Import button missing, except DEV
Going to the STMS in DEV system, the button is present, although the configuration of active and distributed.
What could be wrong?

Accepted Solutions (0)

Answers (2)

Answers (2)

ashish_mishra2
Contributor
0 Kudos

Hi,

Just change the parameter NO_IMPORT_ALL value to 0 in STMS -> SYSTEMS --> Parameters.

Setting this parameter to 1, would disappear the mass import button.

This is an online change, no restart required. Just change it, save and distribute.

Cheers !!!

Ashish

former_member226585
Participant
0 Kudos

It is my parameters

It is my button

former_member188883
Active Contributor
0 Kudos

Hi Evgenly,

Could you refer the link below to get your configuration done

http://www.sapsecurityexpert.com/2011/07/disable-transport-all-button-in-stms_import/

Hope this helps.

Regards,

Deepak Kori

former_member226585
Participant
0 Kudos

I set NO_IMPORT_ALL to 0 and i see next picture

I DONT NEED button MASS IMPORT

former_member188883
Active Contributor
0 Kudos

Hi Evgenly,

The correct settings are as attached.

Hope this helps.

Regards,

Deepak Kori

ashish_mishra2
Contributor
0 Kudos

Hi Evgeniy,

Ohh..I see.

Then in such case below note should resolve your problem.

Could you please check in SNOTE and apply, if this note is applicable for your system.

Note 1230586 - STMS: Import all-button displayed

Cheers !!!

Ashish

former_member226585
Participant
0 Kudos
former_member226585
Participant
0 Kudos

this note has implemented

Former Member
0 Kudos

That message just means that you can't set it as a global parameter, which would be valid for all systems.  Just follow the instructions from Deepak as before, but do NOT set check the "global" box.  Repeat the process for each of the other systems.

former_member226585
Participant
0 Kudos

Comrades, once again showing the settings in the CTMC and unnecessary button!


former_member188883
Active Contributor
0 Kudos

Hi Evgenly,

Could you check with an SAP restart. Sometimes it helps in updating the correct values

Regards,

Deepak Kori

Former Member
0 Kudos

Hi Evengiy,

                 Can you please check the transport strategy by using below procedure.

1.Goto STMS

2.Overview Transport Routes

3.Double click on your DEV system and in Queue-controlled transports choose Single transport

Thanks and Regards,

Kunal Gahlot

former_member226585
Participant
0 Kudos

problem not solved

Former Member
0 Kudos

Hi Evgenly,

                 You can try out below method:

revert all you settings to previous condition ,then logout from SAP system.

Login again and change all the settigs to No Import All ,logout and login and see whether it works.

If above method deos not work then let us know.

Thanks and Regards,

Kunal Gahlot

former_member226585
Participant
0 Kudos

This problem appeared after the addition of the road transport group transfer

Former Member
0 Kudos

If you have NO_IMPORT_ALL set to 1, then check if you set filter by project. If yes delete it or set to contain * and check again.

Former Member
0 Kudos

The settings in your screen print are for system A01.  The import-all button is for system A02.  What are the settings for system A02?

Former Member
0 Kudos

Hi Evgeniy,

This does not match in anybody's case.(system A01 parameters and system A02 buttons)

instead please check the parameter settings of system A02 and A02 buttons.

Regards,

Nag

former_member215981
Active Participant
0 Kudos

Hello,

The "import all" button is dependent on the import strategy that you
choose. You can see your import strategy if you double click on the
SID in the graphical editor of STMS. If you choose mass imports
as the strategy then an import all button will appear in the import
queue. If you do not wish this then please change the strategy to
single import.
The change needed to be made from the domain controller.
All changes for TMS should be performed via the DC.

It is displayed in STMS if the transport strategy is queue with mass
import. This is represented by tp parameters (e.g. no_import_all = 1
means that you have no mass import, import_single_strategy means queue
import with single import or workflow strategy). Do not change the
parameters manually, but set the right transport strategy in the
transport routes.

Please refer to help.sap.com in the following path:
Transport Management System (BC-CTS-TMS)  > Configuring TMS  >
Choosing the Transport Strategy and under section Prerequisites
you will see the steps to configure the single transports strategy.

Best Regards,

Yong Luo