on 01-08-2013 1:06 PM
Dear Experts,
I implemented geomaps and it works fine with out open URL. but if i try with open url and click on the some POI on map and the on side arrow i can see some thing loads but then immediately it say "Content Unavailable".
I use the following syntax for geo maps open url.
="iDocID=AZkCFyVA0h5KsUx5rZPbhNo&sIDType=CUID&sType=wid&sReportName=HR&sRefresh=Y&sReportPart=testc&lsSCountry="+[Country]
could you help me on this error.
i tried in forum for some similar issue. but coult not fine one.
Thanks,
Chandru
Hello Chandrasekar,
Any luck with this.
I am also getting this error while a opening a child report.I have tried using a vertical table and a line chart with only 1 measure in child report.
Any help will be greatly appreciated !
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hello Chandrasekar,
Below is my OD column syntax.
="iDocID=AWLCwsOH3L9Clbd4wi.Qrvo&sIDType=CUID&sType=wid&sReportName=poi&sReportPart=line&sRefresh=Y&lsSstate="+[Crnt Yr].[State]
The child report name is "poi" which has only one tab with 1 line chart.
Tab Name= Report 1.
Line Chart Name= line.
Coud you please help me to make this work ?
Hi Shantanu,
="iDocID=AWLCwsOH3L9Clbd4wi.Qrvo&sIDType=CUID&sType=wid&sReportName=Report 1&sReportPart=line&sRefresh=Y&lsSstate="+[Crnt Yr].[State]
or try below one:
="iDocID=AWLCwsOH3L9Clbd4wi.Qrvo&sIDType=CUID&sType=wid&sReportName=Report%201&sReportPart=line&sRefresh=Y&lsSstate="+[Crnt Yr].[State]
As told by Chandrasekar earlier you need to use Report name as "Report 1" which is your tab name.
AWLCwsOH3L9Clbd4wi.Qrvo is your document id for POI.
Please try to change the syntax if it works or not.
Regards
Shabnam
Hi Shabnam,
Can you pls help me with working offline with the reports.
Below is my thread
Hi Chandrasekar,
I have also faced similar kind of issue. Kindly ccheck your idoc/report/report part name again.
My issue was resolved when I replaced report part name with correct block/chart name which I wanted to display.
Kindly try with below syntax also.
iDocID=AZkCFyVA0h5KsUx5rZPbhNo&sIDType=CUID&sType=wid
&sReportName=HR&sRefresh=Y&sReportPart=testc
&lsSCountry=[Country].
Kindly let me know if issue still persists.
Regards
Shabnam
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hello Chandrasekar,
Can you tell us what is the content of your report "test".
There are contents which are not supported in the BI application.
Please refer to this discussion : http://scn.sap.com/thread/3165496
Regards,
Larbi.
User | Count |
---|---|
86 | |
10 | |
10 | |
9 | |
7 | |
7 | |
6 | |
5 | |
4 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.