cancel
Showing results for 
Search instead for 
Did you mean: 

Function module "DSWP_BPM_ALERT_REPORTING_NEW" not found. ( RFC destination: NONE ; sy-subrc = 1 )

former_member210731
Participant
0 Kudos

Hi,

I am working to configure Business Process Monitoring in the following steps, solman_setup -> business process monitoring -> step 1.1 (load alert data into BW Cube)

but after the step is execute it gives the below error..

Function module "DSWP_BPM_ALERT_REPORTING_NEW" not found. ( RFC destination: NONE ; sy-subrc = 1 )

Let me know how to get the same resolved.

Regards

Mahendra K

Accepted Solutions (0)

Answers (2)

Answers (2)

keiji_mishima
Active Contributor
0 Kudos

Hi Mahendra K

I guess your SolMan is SOLMAN 7.1 SP5. Or more than Sp5....

Do you know which ST-BCO is install in your solman ?

In the configuration guide, SP6 and ST-BCO SP3 are recommended...

Not sure this is relevant in your case...

If BCO is less than the SP level, how about patching SP of ST-BCO ?

The message sounds like,  function module DSWP_BPM_ALERT_REPORTING_NEW is missing.

But if I look at some SolMan where I use, I can see the FM...

If you look at SE37, can you see FM ?

Best Regards
Keiji

former_member210731
Participant
0 Kudos

Hi Keiji,

Thanks for the response.

I am using ST 05 and my BCO 02 and working to upgrade the BCO to recommended patch level (this could be issue).

Also the said FM exist, please find below screenshot of the same.

Let me know incase you need any additional information.

Regards

keiji_mishima
Active Contributor
0 Kudos

Hi  Mahendra K

Thank you for the screen shot.

OK, the function modul exist....

As far as I check the FM usage, it is only used in the FM DSWP_BPM_ALERT_REPORTING_MIGR.

And If I check Note related to the FM, I found Note 1779712.

If possible apply above note and execute the corresponding SOLMAN_SETUP.

Result of a execution, you may see background job

SMSETUP: AGS_BPMON_ALERT_BW

if it fail again, let's check job log in SM37...

but this seems like some product issue. So I think you have better to report OSS.

Best Regards

Keiji

former_member210731
Participant
0 Kudos

Hi Keiji,

I have implemented the specified note and rerun the job and now is was run sucessful.

Thanks for your help, Also I am looking to configure the BPM for O2C and P2P process in Solman 7.1 SP5.

Can you please suggest me suitable link for the same?

Regards

Mahendra K

former_member210731
Participant
0 Kudos

Hi Keiji,

Any help on the below error ofr BPM setup

keiji_mishima
Active Contributor
0 Kudos

Hi Srirangarajan

Do you configure the key figure ? (Which key figure, data collection frequency etc)

If it is BPMon Monitor, you need to configure, key figure, threshold value, data collection frequency at least. And then after saving the configuration, please choose generation first.

And then conduct activation.

If it is Analytics monitor, you need to configure the key figure and choose group by flag that you want to aggregate.

Analytics Monitor can configure under the logical component.

And BPMon Monitor under business process.

*Both Monitor show up under the logical component. To distinguish, you better to put some

pre-fix when you create monitor (e.g BPMon-xxx, BPA-XXX) or you can also distinuguish by

adding addtinal field colled flavor in the right slide list.

In the screen, the status field of monitoring object show initial. So I wonder whether you did key figure configuration etc and generation.

If error really occurs, we can see more detail info in application log. (SLG1).

Object SOLAR

Subobject BPMON*

Here you might get some info.

Best Regards

Keiji

former_member210731
Participant
0 Kudos

Hi Keiji,

I am new to BPMon, Could you help me where to configure the key figures

Regards

former_member210731
Participant
0 Kudos

Hi Friends,

Any update

Regards