on 08-03-2012 1:59 PM
Dear all ,
I have created new inspection type 90 ( with task list usage = 90 ) by copying 10 (Task list usage = 10 ) .
90 is assigned in the lot origin 10 as Variant 02 .
Inspection type 10 is activated , and inspection type 90 is preferred inspection type Activated :
now when i am creating PGI against sales order inspection lot is created with inspection type = 10 .
but i have activated both 10 & 90 and here 90 is preferred inspection type so system should create lot with inspection type 90 .
Pl guide where i am missing .
regards ,
Hi Feed,
Check if you have assigned insp type-10 to the delivery category in Config (SPRO --> QM --> Quality Insp --> Insp Lot Creation --> Insp At Shipping --> Assign Inspection Type to Delivery Category).
System takes this as preferred even if other type has mentioned as preferred in Material master.
Change this & try... this would work.
Regards,
Anup
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Feed,
Before that, is there any specific business requirement that forced you to define new insp type-90 (Copying from 10) ?? Coz in that case, you can make a new entry with origin-10 with Delivery Category (SD Customised) with insp type-90 in SPRO.
If that's not possible, due to some process issue then I would recommend you, to just remove insp type-10 from Origin-10 line... Do not enter insp type-90 for origin-10 line or else this will be populated for all insp lots.
Hope I was clear while explaining.
Regards,
Anup
the requirement i have defined this because : insp type 10 having task list usage 10.
Same task list usage is used for 04 type . but the inspection plan for 04 & 10 type are different .
so when i create the inspection lot automatic assignment is not happening for different Task list Usage.
That's why i have created new insp. type 90 with separate task list usage =90.
I will try below : And let you know the feedback
(If that's not possible, due to some process issue then I would recommend you, to just remove insp type-10 from Origin-10 line... Do not enter insp type-90 for origin-10 line or else this will be populated for all insp lots.)
Dear Anup ,
i have tried the same by :
Spro --> Inspection lot creation --> Inspection at shipping --> Inspection type for delivery Category =
I have removed the line Insp type origin 10 assignment with Inspection type 10 .
I have not added any line in this setting .
Now system is doing following :
algorithm to search for an alternative inspection type:
The system searches the inspection setup of the material for a preferred inspection type, or searches in the table "Assignment Inspection Lot Origin - Inspection Type" for an inspection type that is assigned to the inspection lot origin as variant 01.
( here in material master i am using 10 as active & 90 as active with preferred tick .
now system is taking 90 type as i required .
but will it work normal for the material having 10 inspection type ? pl guide .
Dear Feed,
Good that it's working now and picking up insp type-90 as required...
But it should also work normal by having insp type-10 and for that, did you tried to assign insp type-10 to relevant Delivery Types in config ? Path: SPRO --> QM --> Quality Insp --> Insp Lot Creation --> Insp At Shipping --> Assign Inspection Lot Origin to Delivery Type.
Try this and hopefully should work as well... revert with results.
Regards,
Anup
Feed, I have a question here out of curiosity! Possibly you would have tried this also.
If doesn't work, you can try by assigning only 90 as inspection type in material master and removing 10 from material master. Not from lot origin.
Thanks
Regards,
Anand
User | Count |
---|---|
91 | |
10 | |
10 | |
6 | |
5 | |
5 | |
5 | |
3 | |
3 | |
3 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.