Result recording in Characterestic MIC

[former_member223028]

Dears

I want to know how we can record the result upper and lower value in Result recording in Characterestic MIC

while creating characterestic MIC both upper and lower control indicatore are become disabled

Pls guid me how we can achinve this

Abu fathima

[anand_rao3 · Accepted solution]

Abu,

I don't know how much this can add value here, as I am not so clear about what is being asked. Do you want to record the results as single value or with intervals?

1. Are you referring an MIC which you created through QS21 with control indicator Classed recording ticked or classed characteristic created through CT04?
2. If earlier is the case, then you must be able to enter lower and upper values in MIC. (NOT at result recording screen)
3. In fact depending upon your tolerance here either system or you can decide class interval and class width.
4. At result recording screen you need not enter the exact reading like in single or summarized recordings.
5. You need enter how many samples you found against certain interval.

Hypothetical example of MIC created through QS21 with classed recording ticked

1. Lower spec limit 10.00
2. Upper spec limit 16.00
3. No of classes 5, class width 1.20, class midpoint 13.00
4. At result recording, you will observe the intervals as 10.00 to 11.20, 11.20 to 12.40 likewise
5. You need to enter how many sample lie in this interval.

Regards,

Anand

[former_member223028 · Accepted solution]

Hi anand

thanks for the reply

i was created a MIC with class charectersic(CT04 intervel is also ticked)

and this MIC is assigned in inspection plan

but when RR is doing i am not see any range in there

what ever range i given system accepting the batch

Pls guide me

while creating Charecterstic in value tab we need to give any values????

Abu fathima

[Former Member]

Either you have selected preset indicators ( if yes then remove the same)

or

You have not ticked on control indicators uppler limit & lower limit while creating MIC

[former_member223028]

Hi sujit ji

While creating mic i was selecting my class characterestic so( i hope) i am not able to tick the control indicatore

so my doubt is that if we use class characterestic in mic we can not record upper and lower limit?

pls advice

Abu fathima

[Former Member]

I think you should put question very specific & make sure that you ask precise question rather then using very genraic terms or asking question very short .

At the first quetion itself why did you not mentioned about class char.This will reduce effort & time.

This can be seen with many qustion that you asked.

This is just my views & suggestion !

Now coming back to ur second thread,

If you want Upper & lwoer limits in MIC when you are using class char then,create the class char with

Interval values allowed

This indicator defines whether you can enter an interval as a value for a numeric char.

Enter range while creating the class char.

[former_member223028]

Hi

sorry for mis lead you in the discussion future i will care it

can you pls tell me how we can enter range while creating class

regards

Abu

[Former Member]

check CT04-->Interval values

[former_member223028]

Hi sujit

i was created a character in inter value ticked and assigned in MIC

while recording the result i didnt feel any difference as system not ask to enter any range

Waiting a reply from you to go further

Abu Fathima

[Former Member]

Dear Abu,

Your initial question was

while creating characterestic MIC both upper and lower control indicatore are become disabled

Which can be solved by entering the "range in Class char"

Now coming back to your second  question

but when RR is doing i am not see any range in there

You can not enter results as range...but you can maintain it in  MIC as UCL & LCL .

I hope you are getting ,What I mean to say.

[former_member223028]

Hi sujit

Pls tell me how to give range in class char

so i think my problem is solved

Abu

[Former Member]

If you want Upper & lwoer limits in MIC when you are using class char then,create the class char with

Interval values allowed

Then go to values & put

10

20 ( for example)

while creating MIC with reference to class char system gives you msg ,that limits are maintained as per class char.

Now go to "Quantitative data  " and put the limits( 10 & 20)   ..save !