SLD No own Business system

[former_member192238]

Hi Team,

In our Quality system environment, messages are failling with below error message all though the Business System existing for our quality system in the SLD till yesterday it is working fine .

I tested, SLDCHECK, SLDAPICUST and all other possible RFCs but still i am seing this error message in the sxmb_moni.

please suggest for the resolution.

<SAP:Code area="INTERNAL">SLD_NO_OWN_BS</SAP:Code>

  <SAP:P1>NXP</SAP:P1>

  <SAP:P2>510</SAP:P2>

  <SAP:P3 />

  <SAP:P4 />

  <SAP:AdditionalText />

  <SAP:Stack>Error while reading ID of own business system from the SLD for system GSQ and client 500SAP:Stack>

Thanks

Praveen

[Former Member · Accepted solution]

Hello Praveen,

Please follow the below mentioned steps to get rid of mentioned issue:

1. Check the SECSTORE T-Code for SLD API and compre the error you are getting in SLDAPICUST.

2. Then go to UASE16N T-Code and delete the entry for AREA 'LD' from "LCRT_INDX" table.

3. Then you will be able to access sldapicust and make the new entries for SLD.

4. After that check sldcheck.

Hope this will help you!!

Rgds,

Nilutpal.

[former_member192238 · Accepted solution]

Thanks Nilutpal,

Your solution has solved my problem.

Regards

Praveen

[aashish_sinha]

Hi,

Can you please check SXMB_ADM-.> IE Configuration-> Specific Configuration for correct RFC destination of PI/ECC - Quality?

This may be a possible reason if all RFC destinations and TXN - SLDAPICUST and SLDCHECK are working in ECC quality. IE Configuration should point to PI's RFC destination created.

Regards

Aashish Sinha

[former_member192238]

Thanks Every one,

I have checked my configuration in ECC as the system ECC system was upgraded some changes have been done as  SLDCHECK in ECC showing there is no connection to SLD.

I will check with Basis guys and i will revert back.

Regards

Praveen

[Former Member]

Hi Praveen,

Please Check the following Steps -

1) Run the SLDCHECK in your ECC System and check if the SLDCHECK is successful or not.

2) IN SLDAPICUST the password of the user has changed. Try using the user XIAPPLUSER.

3) Check the RFC (SAPSLDAPI, LCRSAPRFC) in SM59 of the ECC System.

If the above steps are working fine for you , then Check the SLD configuration of SAP PI System one again.

Carry out a Full Cache refresh with the below link -

http://<hostname>:50000/CPACache/refresh?mode=full

[markangelo_dihiansan]

Hello,

Can you execute the function module LCR_LIST_BUSINESS_SYSTEMS and then see if your business system is listed there?

If not, you need to execute the function module LCR_CLEAR_CACHE.

Hope this helps,

Mark

[former_member192238]

Hi Mark,

I have executed the Functional Module LCR_LIST_BUSINESS_SYSTEMS i am able to see my Business system of DEV,QUAL,PROD.

For TCODE SLDAPICUST in PI it is working fine in ECC if i am runing the same SLDAPICUST i am getiing following message.

System-dependent data for entry /SLD/HTTP/PWD/ALIAS/SAP_CONFIG changed:

(GSP|0020572647) / (GSQ|0020572647)

Because of this change for ECC this issue may be there please suggest me.

Regards

Praveen

[markangelo_dihiansan]

Hello,

Can you go to Integration Directory -> Business System -> Click your Business System -> Communication Component -> Adapter Specific Identifier

You should see if there is an entry for Logical System, R/3 System ID and Client

If there are none, edit the business system and then click

Compare With System Landscape Directory -> Apply

Hope this helps,

Mark

[former_member192238]

Mark,

I am able to see entry for Logical System, R/3 System ID and Client.

Regards

Praveen