on 04-16-2012 9:55 AM
dear gurus,
i've a infopackage which is in process chain,
it failed with message-"ERROR OCCURRED IN THE DATA SELECTION"
in details tab under extraction.
so the no. of data packets are 0.
please help me with solution.
and how to trigger the processes which are below this task.
regards,
ratin.
Hi,
Kindly check whether you have applied any selections (under the data selection tab -1st tab of your infopackage). if there is a selection then check whether the FROM value is less than the TO value.
Regards,
Sathyan
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
As our friend said, check the data in RSA3 (R3 side), if the data is correct .then check the selections in Infopackage and also check any routine or converion exits are maitaining there at infopackage level.
Check these,
http://scn.sap.com/thread/1649674
Regards,
Anand.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Ratin,
This can occur due to bug in infopackage or incorrect data selection in your infopackage.
Check data selection in the info package and start job again after changing the technical status to red and deleting the error request from the data target.
Check the job in source system
1. Copy the request no in the header tab of info package in your BW system
2. Open the source system. SM37 tcode. copy and execute.
3. If job was cancelled check the error message. (Please post the error message if possible)
Regards,
Shilpa
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Ratin,
If it is trfc issue as said above, then refer to following doc to solve the issue:
http://scn.sap.com/docs/DOC-26591
How to proceed the PC, after completion of IP?
Go to table:RSPCPROCESSLOG in SE16.It is the table which gives logs of the Process chain.After solving the infopackage step follow the below steps
Go to Display messages by right clicking of your Previous step from where you need to proceed the chain
Go to "Chain" tab and copy "Variant" and "Instance"
Go to SE11 and Select table RSPCPROCESSLOG
Paste the "Variant" and "Instance" and execute it, and the value of the other fields are returned: LOG_ID, TYPE, BATCHDATE and BATCHTIME
Go to SE38 and enter RSPC_PROCESS_FINISH
Enter the values in the fields received from RSPCPROCESSLOG table. Additionally, make the STATE as "G‟ -> Execute('G' refers to making the step green and triggering furthur).
hope this helps
Regards,
Harish.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi:
I think you should check the following point:
1 check datasource use RSA3 in source system
2 check the job log in source system use sm37, the job name is BI<Request number>
3 check the IDOC status BW -> Source system and Source system->BW. You can find the idoc number in infopackage monitor and use we02 or we05 check idoc..
According to the above checking step , you can determine what happening,and then take further action.
Best Regards
Peng
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
Did you put any selections in your InfoPackage.
May be the values you given are not correct or in correct format for that character.
Check this link...
http://scn.sap.com/thread/2003856
Regards,
Aravind.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
Check whether RSLOGSYSMAP table has got correct entries. You can try running this datasource in RSA3 in ECC side. You can even debug the extraction by using /H while running RSA3.
Take any ABAP er's help...
Regards,
SUman
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
85 | |
23 | |
11 | |
9 | |
8 | |
5 | |
5 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.