Message not visible in RWB ? ...But able to run the scenario ?

[Former Member]

Hi Experts

I am XI learner...and problem is for File to File scenario, I done every thing and

receiver side i am able to see the message. But problem is i want see the

message in different stages ? but RWB nothing is visible(<u><b>SXI_MONITOR</b></u>)..!!! Any settings i need to do for this ?

Adv..thanks and regards

Rakesh

[prabhu_s2 · Accepted solution]

SXMB_ADM --> Integration Engine Configuration --> Specific Configuration --> Add the parameter ,

Category --> RunTime LOGGING_SYNC set to 1.

[prabhu_s2 · Accepted solution]

also u can look to SXMB_ADM/Conf Integr Engine for Parameter Monitoring

[Former Member · Accepted solution]

Hi Prabhu

Thanks a lot for imme...response

already settetings are done..!! i checked in the parameter Monitoring also..!

regards

Rakesh

[Former Member · Accepted solution]

Hi,

Check this blog by Michal.

/people/michal.krawczyk2/blog/2005/05/10/xi-i-cannot-see-some-of-my-messages-in-the-sxmbmoni

Regards,

Sudheer.

[Former Member · Accepted solution]

Rakesh,

Configure the parameters as specified in the Blog by Michal. Also remember to restart the XI server after configuration, since the changes will not take place till the restart.

Regards,

Jai Shankar

[prabhu_s2]

also one simple check....in the selection screen of the sxmb_moni check for the date/time range.

[Former Member]

please add an entry in sxmb_adm

runtime (catgory) logging (parameter) 1 (value). if this is set. still you dont see your message . please select correct and time in our sxmb_moni selectionscreen.

please reward points

Thanks

Sreeram.G.Reddy

[Former Member]

Hi All

Thanx for all responses ...

but still it not displaying any messages? Still is there any other chance to

miss out ?

regards

rakesh

[prabhu_s2]

just try with these:

SXMB_ADM -> Integration Engine Configuration -> Specific Configuration

Create entries:

RUNTIME LOGGING 1

RUNTIME TRACE_LEVEL 3

also check with <a href="http://Unable to see any message in sxmb_moni.">this thread</a>

[Former Member]

Hi Prabhu

I have already done this...

Is there any other reason? pl....

regards

rakesh

[Former Member]

are able to see output of this interface. what is kind interface is this is it File to file etc.

Thanks

Sreeram

[prabhu_s2]

okie just reading thru ur post again....are u not getting any mesage in sxmb_moni regarding ur interface?

[Former Member]

Hi

Yes...it is simple file to file scenario...!!!

Only problem is i am not able to see the message in RWB ..!

regards

rakesh

[prabhu_s2]

are u sure the file contents are transferring...also check with CC in component monitoring for is it showing any errors?...source: RWB in initial screen

[Former Member]

in RWB which option your using to see message. which sp you are using

[Former Member]

Hi Rakesh,

If i clearly understood your problem

Your scenario is executed. You are able to see the output file.

There is an entry for the same in SXMB_MONI( Confirm ).

There is no entry in RWB.

Regards,

Sudheer.

[Former Member]

Hi Sudeer

Exactly....the same problem

regards

rakesh

[prabhu_s2]

check in communication channel of component monitoring in rwb

[Former Member]

Hi,

Check my blog some of the porints..it will helpful for your requirement..

/people/venugopalarao.immadisetty/blog/2007/01/24/troubleshooting-file-to-idoc-scenario-in-xi

Regards,

Venu.

[Former Member]

Hi,

Just give a try.

Do some mistake in the scenario first at the integration engine level and next at adapter engine level and then check if an entry is made. First do some mistake in mapping and then give some erroneous input in communication channel.

Regards,

Sudheer.

[Former Member]

Hi

Just wait i am doing one by one as per your suggestions

regards

rakesh

[Former Member]

In RWB please use Message Monitoring option in that select intergation serever option and select from databas e option just to right and select correct date and time you exceuted you should find your entry.

Thanks

Sreeram.G.Reddy

[Former Member]

Hi All

I tried with all the options given...but still not displaying any messages in RWB

SXMB_MONI..

What should i do on this?

regards

rakesh

[Former Member]

Is input file is empty. please check th size of the input file.

[Former Member]

Hi Sreeram Reddy

It is just 1KB file...not empty

regards

rakesh

[Former Member]

can you open the file see what is data it has

[Former Member]

Hi,

Did u execute transaction sxmb_moni in XI, chose the correct Date/time selection parameters and checked it.

Were u able to see ur message there.

Regards,

Sudheer

[prabhu_s2]

are u able to get it seen?