on 01-24-2007 9:06 AM
Hi all,
My scenario is RFC>XI>FTP,
I need to receive allert if FTP Server is not responding.
I configured the rule, but however I don't get the allert to allert inbox.
Will appreciate all help,
Thanks a lot
Thanks a lot for your replies
Yes, exactly due to the weblog
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Elad,
As Bhavesh already pointed out, you should be on atleast SP14 to receive adapter failure alerts.
Also test your alert category using the report "RSALERTTEST". Check if this delivers an alert to your alert inbox.
If you feel alerts are getting triggered but not delivered, you can inspect ST22 for any short dumps
Regards,
Jai Shankar
Elad,
This shows your Alert category is working fine
You have selected your Alert category for testing. Right?
Now what are the configurations you ahve done for your alert category in Alert Configuration(RWB) ?
Also is the alert getting trigerred for mapping errors? You can check this by giving a wrong input...
Regards,
Jai Shankar
Elad,
1. Check for Integrtaion Engine Alerts first . Make some mappig error and see if the alert is triggered.. If yes , then do the following for Adapter Engine alerts and check if they are triggered
<i>If still no sucess, make everything * --> and in where did the error occur make it " Adapter Engine --> File adapter " and check if the alert is triggered.</i>
2. If the integrtaion engine alerts are not getting triggered due to mapping errors, check for dumps in st22. Make the user id as * and see if there is some authorization error for the XIRWBUSER.
3. Also, test the RFCC destination CentralMonitoringServer-XI alerts in Sm59.
Regards
Bhavesh
Hello,
Jai and Bhavsh,
I tried all the steps that you recommend me and at the moment the alerts doesn't work.
I made a problem in the mapping and the alert doesn't work.
I checked the TCODE st22 and not found any damp.
I checked the TCODE m59 and everything looks OK.
May be do you have more idea?
May be I can upload screen shot?
Thank you for all your help
Elad
Elad,
Suppress Multiple Alerts of this Rule is used so that the Alert will be triggered only the first time an error occurs satisfying the rule. Only after the Alert has been CONFIRMED in the Alert Inbox of the recipient, the next Alert will be triggered in this case.
Unchecking this option will trigger the alert for every error that satisfies this alert rule.
Regards
Bhavesh
Elad,
Did you configure Alerts as shown in this blog?
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step
Adapter Engine Alerts can be triggered only if you are Sp14 and above.
Regards
Bhavesh
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Elad,
that could have some reasons.
- Condition for raise the alert
- Something went wrong at ALRTCATDEF
- Did you put the right user?
- The inbox from RWB has some strange behavior. Better look via ALRTINBOX
Have a look to Michals blog <a href="/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--troubleshooting-guide">XI: Alerts - Troubleshooting guide</a>
Regards,
Udo
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Elad,
have you configured an alert category with TCODE: ALRTCATDEF?
Hope this help
Francesco
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
88 | |
23 | |
11 | |
9 | |
8 | |
5 | |
5 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.