IDOC ot File

[Former Member]

Hello everybody,

does anybody know how send form IDOC or RFC adapter to File adapter.

i have tuning all parametrs in Integration Repository(Design) and Integration Directory(Configuration), but i do not know how tining Communication Channel for Sender Agreement.

Regards Anvar

[Former Member · Accepted solution]

Hi everybody.

thanks for all answers.

anybody know how program ID need writing for IDOC CREMAS.CREMAS01 ?

[Former Member · Accepted solution]

Hi Anvar,

Program ID is not needed for IDocs on sender side.

Regards,

Uma

[Shabarish_Nair · Accepted solution]

in case of program id for RFC's ref : /people/shabarish.vijayakumar/blog/2008/01/08/troubleshooting--rfc-and-soap-scenarios-updated-on-20042009

[Former Member]

Anvar could you pls give me your email address, I would like to email you snapshots of such scenario which is in step by step form.

Regards,

Ashish

[Former Member]

thank anybody and special for Shabarish Vijayakumar.

[Former Member]

Therefore, does IDoc come to XI only? And is there one communication channel?

[Shabarish_Nair]

in R3 you can create these to sent idoc data from XI to R3.

SM59 - R3 connection pointing to XI

WE21 - define the port with the above dest.

WE20 - Partner profile type outbound (to sent Idoc from R3 to XI)

And is there one communication channel?

>>> to receive IDocs into XI you dont need a adapter, but to sent IDoc from XI to R3 u can use the receiver IDoc adapter.

[Former Member]

Help me anybody ...

for setting send IDOC from R/3 System to XI

i am open /people/ravikumar.allampallam/blog/2005/02/23/configuration-steps-required-for-posting-idocsxi

but do not understand where setting

1. Creating RFC Destination by "Enterprise" ? (by my XI)

2. Creating a Port by "SAPENT" ? (by my XI)

3. Receiving System by "HTTPSO" (by my XI)

Then i am do not understand what setting to R/3 System?

[Shabarish_Nair]

<i>1. Creating RFC Destination by "Enterprise" ? (by my XI)</i>

>>>

create a destination of type R3 in the tcode SM59 of your XI server. in this destination give the detials of your R3 system you want to connect to.

<i>2. Creating a Port by "SAPENT" ? (by my XI)</i>

>>>>

in tcode idx1 of XI, create a port and refer the above destination you created here.

<i>3. Receiving System by "HTTPSO" (by my XI)</i>

>>>>

create a TS and BS for your R3 system.

[Former Member]

Thanks everybody.

I am understand and try send IDOC from R/3 system to XI.

Regards Anvar

[Former Member]

Hi.

well i am not given IDOC from XI?

i am only send to XI IDOC ?

[Shabarish_Nair]

in case you need to sent Idocs from R3 to XI, you need to do some basic settings as follows;

In XI

SM59 - R3 connection pointing to R3

IDX1 - define the port with the above dest.

In R3

SM59 - R3 connection pointing to XI

WE21 - define the port with the above dest.

WE20 - Partner profile type outbound (to sent Idoc from R3 to XI)

[Former Member]

Hi Anvar,

Yes, for sending IDoc from R3 to XI program id is not needed.

Hope this will clarify your doubt.

Regards,

Uma

[Former Member]

Hi Anvar,

In addition Anuradha's points, few configurations settings are need to be done for IDoc scenario like creating ports and partner profiles.

Regards,

Uma

[bhavesh_kantilal]

Hi,

To send an Idoc from R3 system to XI, following setting are needed,

R3 system.

1. Create SM 59 RFC destination to XI,.

2. We21 - Create port to XI.

3. We 20 -- Maintain Partner Profile for the outbound Idoc.

XI SLD

1. Create technical system for R3 system

2. Create Business System for the Client of the R3 system.

use this business system as your sender Business System in the Receievr Determination.

More on these blogs,

/people/prateek.shah/blog/2005/06/08/introduction-to-idoc-xi-file-scenario-and-complete-walk-through-for-starters

/people/ravikumar.allampallam/blog/2005/02/23/configuration-steps-required-for-posting-idocsxi

For sender RFC , these blogs,

/people/michal.krawczyk2/blog/2005/03/29/configuring-the-sender-rfc-adapter--step-by-step

/people/shabarish.vijayakumar/blog/2008/01/08/troubleshooting--rfc-and-soap-scenarios-updated-on-20042009

Regards,

Bhavesh

[Former Member]

Hi Anvar,

Idoc adapter does not need a sender communication channel and sender agreement as it resides on abap stack.

RFC adapter needs sender communication channel and sender agreement,

in RFC sender communication chaneel,u need the specify the program id which is assigned for the report which triggers the RFC in R/3.

Regards,

Anuradha.