cancel
Showing results for 
Search instead for 
Did you mean: 

lot not getting geneated during MFBF

Former Member
0 Kudos

Dear Expert

i have maintian 04 inspection type in material master. i am using repetitive process .At the time of MFBF quality inspection is not getting generated.

what else i am missing , kindly have a look and give your ideas on this .

regards

v.k

Accepted Solutions (0)

Answers (3)

Answers (3)

former_member42743
Active Contributor
0 Kudos

BTW: Are you sure you are using an 04 inspection lot?

Repetitive mfg should be using a 13 inspection origin. Not 04.

http://help.sap.com/saphelp_46c/helpdata/en/be/00bbdeca5311d2961800a0c930e04c/content.htm

FF

former_member587434
Active Contributor
0 Kudos

BTW: Are you sure you are using an 04 inspection lot?

>

> Repetitive mfg should be using a 13 inspection origin. Not 04.

>

> http://help.sap.com/saphelp_46c/helpdata/en/be/00bbdeca5311d2961800a0c930e04c/content.htm

>

> FF

Just to correct you FF, insp type 13 work same as insp type 03. So you can use insp 13 in place of 03, but 04 (GR against PO) is common in both cases.

former_member42743
Active Contributor
0 Kudos

Thanks for the info. I've not had much use to use repetitive mfg with my clients. It's been a long time since I've played with it.

FF

Former Member
0 Kudos

Dear Expert,

kindly give your ideas into this matter.waiting for your feedback.

Regards

V.K

Former Member
0 Kudos

1.Check In MRP view ProdVersion must be maintained & correct.

2.BOM and routing bmust be checked.

3.Cost collector should be fine.

Former Member
0 Kudos

Dear Sujit

I checked everything and its fine

in qa its happening but in dev its not happening all customization as well as master related settings are same

kinldy suggest what needs to be checked.

former_member42743
Active Contributor
0 Kudos

Sorry,

If it works in one system but not the other than everything is not the same!

I would hope your config is the same of course since you probably have a tight process around doing and moving config. So more than likely the difference is still a master data item. However, since we are talling about it not working in a DEV system, it could be a config issue. But my guess is still master data.

While this is seems obvious, it's easy to miss and commonly is. I've done it quite a few times over the years! So now I only use QA08 to add and activate inspections which solves that issue. Are you sure the "Active" indicator is clciked on in the mateial master for the inspection type?

FF

Former Member
0 Kudos

Dear FF

Each and every thing i have checked and found ok in material master.There is nothing diff. in config. as well.

kindly suggest if any sap-note is missing or tell me the proces for QM activation for Repetitive process.

Regards

v.k

anup_patil3
Active Contributor
0 Kudos

Hello Vimal,

If it worked in Dev but not in QA then, as forum member/s said, there must be something missing in QA.

Check 'Control Insp Lot' selection in Inspection Type-04 in a particular Material MAster in both systems.

I don't see any specific other reason for this.

Confirm back.

Regards,

Anup

former_member662213
Contributor
0 Kudos

Hi,

Kindly check the following things:

1. Inspection type "04" is assigned to material master.

2. The check box "Active" has been activated.

3. Inspection type "04" has been assigned to inspection lot origin "04" in the customization.

4. The number ranges for inspection lot origin "04" has been maintained.

Thanks

SUMIT GUPTA