on 02-17-2012 9:03 AM
Hi,
In the CHECKS phase I am getting this error -
ERROR> Errors occurred during ACTIVATION CHECK
(batch job RSUPGRCHECK)
The contents of the summery error log file is as follows.
Details can be seen in the log file of the batch job: RSUPGRCHECK.BCQ
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
ACTIVATION CHECK Errors and RETURN CODE in RSUPGRCHECK.BCQ
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2EER7000 "Reactivate Aggregate 100134 for InfoCube ZCOPA_AB1" " " " " " "
2EER7000 "Structure/Table /BIC/B0000453000 is not active" " " " " " "
2EER7000 "Activate Transfer Rules for InfoSource 0PRODORDER" "Source System ECQCLNT220" " " " "
2EER7000 "Structure/Table /BIC/B0001019000 is not active" " " " " " "
2EER7000 "Activate Transfer Rules for InfoSource 0PRODORDER" "Source System ECQCLNT220" " " " "
2EER7000 "Structure/Table /BIC/B0001085000 is not active" " " " " " "
2EER7000 "Activate Transfer Rules for InfoSource 0PRODORDER" "Source System ECQCLNT220" " " " "
Here is the log u2013
4 EPU201XBEGIN OF SECTION BEING ANALYZED IN PHASE JOB_RSUPGRCHECK_PRE
4 ER7000 "Check for DDic Consistency of BW Objects" " " " " " "
4 ER7003 -
"Check for DDic Consistency of BW Objects"
4 ER7000 "InfoObjects Check" " " " " " "
4 ER7000 "Activate all Dictionary objects ( 2963 ):" " " " " " "
4 ER7854 All DDIC objects have been activated / deleted
4 ER7000 "End of Checks for InfoObjects" " " " " " "
4 ER7000 "InfoCubes Check" " " " " " "
2EER7000 "Reactivate Aggregate 100134 for InfoCube ZCOPA_AB1" " " " " " "
4 ER7000 "End of Checks for InfoCubes" " " " " " "
4 ER7000 "Transfer Rules Check" " " " " " "
2EER7000 "Structure/Table /BIC/B0000453000 is not active" " " " " " "
2EER7000 "Activate Transfer Rules for InfoSource 0PRODORDER" "Source System ECQCLNT220" " " " "
2EER7000 "Structure/Table /BIC/B0001019000 is not active" " " " " " "
2EER7000 "Activate Transfer Rules for InfoSource 0PRODORDER" "Source System ECQCLNT220" " " " "
2EER7000 "Structure/Table /BIC/B0001085000 is not active" " " " " " "
2EER7000 "Activate Transfer Rules for InfoSource 0PRODORDER" "Source System ECQCLNT220" " " " "
4 ER7000 "End of Checks for Transfer Rules" " " " " " "
4 EPU202XEND OF SECTION BEING ANALYZED IN PHASE JOB_RSUPGRCHECK_PRE
Thanks,
Sameer
Hi Sameer,
Good to know about your earlier resolutions.
For current issue , there are many SAP notes available and some states you can ignore this error,
Notes # 1447267, 742219, 1504600
pls let me know if it is helpful or your further analysis.
Regards,
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Rupali,
I am getting below error in CHECKS phase.
ERROR: Errors occurred during ACTIVATION CHECK. For more information, see the log file of the background job RSUPGRCHECK.CTO. The following is the content of the summary error log file:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
ACTIVATION CHECK ERRORS and RETURN CODE in RSUPGRCHECK.CTO
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
4 ER7000 "Check for DDIC Consistency of BW Objects" " " " " " "
4 ER7000 "InfoObjects Check" " " " " " "
4 ER7000 "Activate all Dictionary objects ( 1851 ):" " " " " " "
4 ER7854 All DDIC objects have been activated / deleted
2EER7000 "InfoObject 0TCTIOBJVAL is not" "consistent. Activate it." " " " "
As per above suggestion, I have implemented 458363 NOTE, but upgrade stops again n again in above issues.
Could you please help me in this regard.
With regards,
Nilabh
Hi Sameer,
Pls refer SAP Note # 458363
Regards,
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
That was very much helpul.
After resolving a few errors in the Preprocessing phase now I am getting this
Checks after phase MAIN_SHDRUN/ACT_UPG were negative!
Last error code set: Detected 113 errors summarizes in 'ACTUPG.ELG' Check logfiles 'ACTUPG.ELG' and 'U:\usr\sap\sapbcq\EHPI\abap\log\SAPehpi.ECO'
When I check the 'ACTUPG.ELG file it says -
**************************************************
LIST OF ERRORS AND RETURN CODES *******
**************************************************
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DDIC ACTIVATION ERRORS and RETURN CODE in SAPA-701DDINSAPBASIS.BCQ
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1EEDO519 "Table" "ZBS_JOB_SCHEDULE" could not be activated
1 ETP111 exit code : "8"
I activated the table & did a repeat step but still failing
Thanks,
Sameer
User | Count |
---|---|
76 | |
9 | |
8 | |
7 | |
6 | |
5 | |
5 | |
5 | |
5 | |
5 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.