Solution manager 7.1 and BW

[Former Member]

Hi,

I would like to active the BW inside the solution manager 7.1.

How should I start with that issue?

looking for a good guide.

Thanks,

Lior Grinberg

[mateus_pedroso · Accepted solution]

Hi Lior

Additionally to Diego's recommendation. Check slide 44, 57-58 of the following guide to have all details and recommendations of BW activation.

service.sap.com/rkt-solman => SAP Solution Manager 7.1 => Setup and Operations => Configuration of SAP Solution Manager => Guided Procedure for Configuration of SAP Solution Manager - SOLMAN_SETUP

[Former Member · Accepted solution]

Hi all,

After a lot of work and working with documents like "How to Guide - Interactive Reporting.pdf";

Still I can't active any report related to the BI.

In the solman_setup I did all the instructions and I'm getting this message when I trying to lunch a report in the workcenter of incident management ->reports->launch Message Reporting error message " Error loading template 0SPR_CONTROLLER"

Can anyone help me?

Best regards,

Lior Grinberg

[Former Member · Accepted solution]

Hello Lior,

This issue was discused here: http://forums.sdn.sap.com/thread.jspa?threadID=1892820

This might help you to resolve your issue.

Cheers,

Diego.

[Former Member · Accepted solution]

Hi Experts,

I saw the thread http://forums.sdn.sap.com/thread.jspa?threadID=1892820 and the notes aren't relevant and I have all the necessary authorization (also SAP_all)

But still I'm getting the same error message.

I will add that I run transaction /crmbw/config_wizard and everything looks ok.

Any thoughts?

Best regards,

Lior Grinberg

[former_member182675 · Accepted solution]

Hi Lior

I just solved this problem

you need to load the tamplate in Solution Manager 7.1 in TZ - RSA1

after you load the template from RSA1 BI content you need to activate him

i just write blog on it, if you need help tell me

shavua tov

Naor Shalom

[Former Member · Accepted solution]

Hi Naor,

Please publish the blog URL.

Also How do you active the template in TZ RSA1?

Best Regards,

Lior Grinberg

[former_member182675 · Accepted solution]

Hi Lior

i wait that SCN team will confirm my blog

if you want that i send it to you in private

please give me your mail

Regards

Naor shalom

[Former Member · Accepted solution]

Hi Naor,

I can't add an email to a post.

Can you write in short how to solve the problem?

Or can you look for my name in Linkin and send me a message there?

Best Regards,

Lior Grinberg

Edited by: Lior Grinberg on Feb 15, 2012 5:10 PM

[former_member182675 · Accepted solution]

Hi lior

log in to solution manager - RSA1 - BI content - query elements - query - select object -

in the popup windows search the 0SPR_CONTROLLER - chose transfer -

and then install and install

and check your gmail i attached a word doc

hope it's help

Naor Shalom

[former_member182675 · Accepted solution]

HI to all

please check my blog

http://www.sdn.sap.com/irj/scn/weblogs?blog=/pub/wlg/28686

Regards

Naor Shalom

[Former Member · Accepted solution]

Hi Naor,

Got an 'Item not found' error when trying to access your blog. Please could you email the article directly to 'dmichael1750@gmail.com'

Thanks very much!

Darryl Michael

[former_member80258 · Accepted solution]

Thankyou my friend!

[Former Member]

Hi,

this blog available in new scn under here http://scn.sap.com/community/it-management/alm/solution-manager/blog/2012/02/18/error-loading-templa...

and please check this doc also https://websmp205.sap-ag.de/~sapidb/011000358700000482292011E/SM71_Configuration.pdf

this heps you to do all the needed steps to activate the BI based on the scenario.

Thanks.

Jansi

[Former Member]

Hi,

I have installed solman7.1 and the support pack details .

Basis support pack - XXXXX70209 , ST-PI -XXXXLDR5, ST-XXXXKITL704.I am getting an error while configuring through solman_setup - "Infocubes XXXX not activated " Please activate.

I execute the tcode RSA1 but not able to find any activate option to activate these infocubes.

please let me know the step by step process to activate infocubes in solution manager.

Thanks

Mathew

[Former Member]

Hi,

Have you performed the basic configuration in tx. solman_setup. The required activities for BW activation are performed during this configuration steps.

Cheers,

Diego.