CHECKS AFTER PHASE NTACT_CHK WERE NEGATIVE !!!

[Former Member]

I'm in the middle of an upgrade SAP R3 470 to ECC6. The source system does not have ST-A/PI component or was removed during a previous upgrade. PREPARE has stopped with the error below.

>> 16:50:51 PREPARE: END OF PHASE JOB_TS_UPG41

>> 16:50:51 PREPARE: START OF PHASE NTACT_CHK

SAPup message

SAPup> CHECKS AFTER PHASE NTACT_CHK WERE NEGATIVE !!!

It is recommended that you repeat phase NTACT_CHK

You can exit and restart the phase after the errors

have been corrected. Alternatively, if you know that

the error is not of concern, you may ignore it

and continue with phase INTCHK_GEN

You are urged to repeat phase NTACT_CHK !

- "repeat"

- "init"

- "exit"

- "ignore"

Enter one of these options [repeat] := ignore

SAPup message

SAPup> CAUTION: This operation requires a password.

Contact the SAP Support if you don't know it.

- "continue"

- "cancel"

Enter one of these options [continue] :=

The log NTCHK.ELG below shows the objects were not found. I have tried SAP Note 197334 but the runtime objects do not exist as well. Is there away of re-installing the objects?

What is the password to continue with the upgrade?? Any help will be highly appreciated.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

CHKANT and RETURN CODE in PN400122.HKD

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

2EETP399XRead table "/SSF/BDLFLDS ": pgntab call: table not found.

2AETP399 Table "/SSF/BDLFLDS ": unknown error -9

2EETP399XRead table "/SSF/BDL_DATKEY_INTERNCOPY ": pgntab call: table not found.

2AETP399 Table "/SSF/BDL_DATKEY_INTERNCOPY ": unknown error -9

2EETP399XRead table "/SSF/DHEAD ": pgntab call: table not found.

2AETP399 Table "/SSF/DHEAD ": unknown error -9

2EETP399XRead table "/SSF/DSTATUS ": pgntab call: table not found.

2AETP399 Table "/SSF/DSTATUS ": unknown error -9

2EETP399XRead table "/SSF/DTAB ": pgntab call: table not found.

2AETP399 Table "/SSF/DTAB ": unknown error -9

2EETP399XRead table "/SSF/LOG ": pgntab call: table not found.

2AETP399 Table "/SSF/LOG ": unknown error -9

2EETP399XRead table "/SSF/PTAB ": pgntab call: table not found.

2AETP399 Table "/SSF/PTAB ": unknown error -9

2EETP399XRead table "/SSF/RELID ": pgntab call: table not found.

2AETP399 Table "/SSF/RELID ": unknown error -9

1 ETP111 exit code : "12"

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

CHKANT and RETURN CODE in PN410122.HKD

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

1 ETP111 exit code : "0"

Thanks

[nirmal_konchada · Accepted solution]

Hi,

Check the below note :

Note 179334 - Processing of errors in phase NTACT_CHK

and even this will help you :

/message/7790595#7790595 [original link is broken]

Regards,

Nirmal.K

[Former Member · Accepted solution]

Thanks for your prompt response.

the following solution from SAP support worked.

Please look into the tables from the above given logs in database level

if exists please activate it at R3 level.

Else Please do this,

se37 -> dd_nametab_delete -> tablename

and repeat the phase to continue upgrade.