on 12-13-2010 2:23 PM
Hi Gurus,
we are using NW 7.0 Enterprise portal at SP17, want to configure E2E. So installed solution manager 7.0 EHP1 SPS 25.
Ran the Guided procedure solman_setup successfully. with intitial config, basic config and pending at managed system config.
Here my question is:
do i need to install smd agent on solman? or solman itself comes with agent. i cannot see any agent in mmc on solution manager.
What is SOLMANDIAG and SOLMAN AGENT, SMD Agent and Host agent.
The guide (https://websmp207.sap-ag.de/~sapidb/011000358700000952852009E) says before install SMD agent, install host agent, diagnostics agents are available 7.11 on wards, while installing smd agent sapinst asking SAP Unicode Kernel 711 , but currently my NW Portal system is using kernel 7.0..
Any guide, how to proceed for E2E on nw7.0 SP17 with solman ehp1 sp25( highest availale spack)
Thanks in advance.
Regards
Balaji
Hello Balaji
You can use a SMD Agent 7.11 on your SAP Solution Manager 7.0 EHP1 SP25
There is a standalone DVD available on SAP Service Marketplace install the SMD Agent 7.11 which includes the packages to run sapinst and the 7.11 SAP Kernel.
I would advise you to check the diagnostics agent 7.11 SAP notes and the diagnostics part of SAP service marketplace
[http://service.sap.com/diagnostics]
Kind regards
Tom
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hello Balaji
A reminder: The standalone version of SMD Agent 7.20 is available in the marketplace as well. I recommend that you install it. Follow SAP note 1368413.
I've recently updated the Wiki. You can use it for further reference
-> http://wiki.sdn.sap.com/wiki/display/SMSETUP/Diagnostics+Agents
Best regards,
Guilherme Balbinot
Hi,
I am stuck up at Diagnostic agent installaion at kernel selection( SAP Unicode Kernel 7.11l)
According to the note ,i have downloaded the material 51036476, but my portal system is I386, where the files contained in kernel directory are for only X86_64 and IA64 bit....but how to get the kernel for I386 system for diagnostic agent installation.
Regards
Balaji
Hi Balaji,
As per the SMD agent 7.11 installation guide (https://service.sap.com/~sapidb/011000358700000952852009E) , Page 6 and 8, you would need to download the standard NW 7.11 DVDSs( usually kernel and Installation master) and SMD agent installation packages from the SMP. Location is mentioned in the guide as well.
For your query that Portal is based in i386, these are two different things. The SMD Agent will be installed with its own kernel and also 7.11 kernel is not support edon 32bit. However the SMD agent will use its own 7.11 64bit kernel and Portal will use its i386 kernel. Hopefully your hardware is able to support both. I recommend to proceed with x86_64 7.11 kernel for your SMD installation. Incase the hardwar does not support this, go for alower release of SMD Agent wherein the kernel supports 32 bit hardware.
Best Regards,
Srikishan
Hello
You may want to review SAP Note 1274287 - End-to-End Diagnostics 7.0 EHP1 SP18 to SP25 to ensure you have meet all the requirements.
Regards,
Paul
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
81 | |
24 | |
11 | |
9 | |
7 | |
5 | |
5 | |
5 | |
4 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.