Getting Error in SM58 and IDX2 while using IDOC from

[Former Member]

Dear All,

Getting error when trying to send FIDCCP02 Idoc from ECC to PI system.

"Basic Type 'FIDCCP02' is unknown"

Getting the same error while trying to import metadata using IDX2 from PI side.

All connections and distribution model are created.

Please help

Regards

[Former Member]

Check thE SAP Note: 1369525, 751839

Thanks,

[Former Member]

Thanks Rahul and Hareenkumar,

We are using SAP PI 7.11 and ECC 6.0.

I dont think both of these patches are useful to me.

Any more suggestions please

[RKothari]

Hi,

Just couple of suggestion more :

1. Check the Basis SWCV in ESR of Quality and Dev. Are they on same service pack??

The info about service packages are available on Details tab.

2. Are you able to import the Idoc in ESR ?? If yes, then check the authorizations for user while performing the activity via IDX2 ?

3. Please check if any dumps are reported either in PI or in ECC system.

4. If still no clue than I guess something is wrong and report it to SAP.

-Rahul

[Former Member]

Hi

01 .Check the Port & RFC destination from IDX1 is it maintained.

02. Check the SM59 RFC connectivity.

Is your QA system Load balancing?

Regards,

Prabhu Rajesh

[former_member518917]

Check if the Basic Type is mapped to the Message type in transaction WE82.

check that the IDoc is available in the ERP system and has been released. The IDocs you use in your business scenario must be released in the ERP system.

[Former Member]

Hi Rtiu,

Message type and baisc types are mapped and released.

Thanks

[former_member200962]

I would suggest that you re-check the config done in SAP and PI (RFC destination, partner profile, port etc).

Are you referring to the valid SAP ECC system? Was this scenario working earlier?

Regards,

Abhishek.

[Former Member]

I have checked all config in the system and seems okie to me.

The scenario is working fine in Dev but we are getting this error in QA. Cehcked all configs and all are as line like Dev.

Strange error it seems!!

[Former Member]

hey,

I checked all config again but getting error while checking ocnsistency in BDM5 on ECC system(E1Q).

It is failing when the messge type FIDCC1 reaches PI QA (X1Q) system and the error states

Message type FIDCC1 is not defined

Please check last line of below message:

E1QCLNT001	Checks in own system E1QCLNT001		
	Message type	@08\QCheck OK@	Message type FIDCC1 is defined
	Segment filtering	@08\QCheck OK@	No segment filtering
	Conversions	@08\QCheck OK@	No conversion
	Partner profile	@08\QCheck OK@	Partner profile has been created
  		                      @08\QCheck OK@	.....Port PI_QA
		@08\QCheck OK@	.....Port PI_QA
		@08\QCheck OK@	.....Packet size 0001
		@08\QCheck OK@	.....Basis type FIDCCP02
		@08\QCheck OK@	.....enhancement
	Port	@08\QCheck OK@	Port PI_QA : To PI Quality System
		@08\QCheck OK@	.....Port type: Transactional RFC
		@08\QCheck OK@	.....port version 3: IDoc record types from Version 4.0 onwards
		@08\QCheck OK@	.....Logical address (destination) X1QCLNT001
	Logical address (destination)	@08\QCheck OK@	Logical address (destination) X1QCLNT001 is defined

X1QCLNT001	Checks in partner system X1QCLNT001		
	Check of own logical system	@08\QCheck OK@	Own logical system is X1QCLNT001
		@08\QCheck OK@	Logical system is the same as the target address
                      
                   Message Type	*@0A\QCheck resulted in error@*	Message type FIDCC1 is not defined

When I am clicking on error it is taking to WE81 on PI side.

So do I need to add this message type in PI system as it is present in ECC side?

Thanks

Edited by: Chanakya Sharma on Dec 10, 2010 12:10 PM

[RKothari]

Hi,

Can you please check if the port in your PI quality system is defined as "SAPnnn".

Is the Port name in PI quality system is same as in development system???

-Rahul

[Former Member]

Hi Rahul,

Port defined in

PI quality system - >SAPE1Q and

PI DEV system -> SAPE1D.

Thanks

[RKothari]

Hello,

Can you check the below mentioned SAP Note:

Note 751839 - IDoc Adapter: Basic type 'XYZ' is unknown

Not sure if it is applicable to your system.

Also check if there are any dumps reported in the system.

-Rahul

[former_member200962]

"Basic Type 'FIDCCP02' is unknown"

FIDCCP02 seems to have been changed/ removed/ deleted.

Please check with the ABAP team and ensure that the IDOC exists.

Regards,

Abhishek.

[Former Member]

Hi Abhishesk,

It does exist.

Thanks