on 05-28-2010 2:33 PM
Hi,
While activating EWA for the system, the problem i am facing is that i am not able to see any systems only the solution is seen.
Please help me with this.
Thanks,
Rohan
Thanks to everyone for the replies.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Rohan,
When you add system to a solution, the only systems that are automatically set to status "Put in Solution" as production systems.
So if you have a solution and you see no systems, if the systems were QAS, DEV, SANDBOX, TEST, and you did not go into change/edit mode and right click the system, and select "Put in Solution", then none of the systems will be visible to EWA, System Monitoring, etc, where ever that solution is referenced.
This is a common mistake that is often made. And it is pretty much the oly reason systems in a solution don't show when that solution is being used, as in EWA . So please check the system in your solution have the status "Put in Solutiion" when you right click on the system in the solution itself.
This should solve the problem.
While Stuart has given you good EWA resources you would not get an EWA for the Solution itself, if you hadn't done the other steps accordingly.
This should resolve your problem.
Regards,
Paul
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi rohan,
Have you added the systems in the logical component and check this logical component added to the solution .
Refer http://help.sap.com/saphelp_sm40/helpdata/en/a2/9b576a334144698f7938507b09b28c/content.htm .
Also do the "PUT IN SOLUTION " steps as mentioned above .
Check :
http://help.sap.com/saphelp_sm32/helpdata/en/e0/72f723d41e0d4986777ed96aeb5cc3/content.htm
Hope it will resolve your issue .
regards,
Nibu Antony
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Rohan,
From what I understand, the systems are missing from the solution. Is that correct?
If so, please check the Solution Landscape - Solution Landscape Maintenance and ensure that the logical components are present there. Also ensure that it is in the solution, that is, the 'Put In Solution' was done.
You can tell by if the system has a green color in the System Group window.
Also check solman_ewa_admin and ensure the systems are active.
Regards,
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi
Firstly check that the system you are settting EWA up for actually exists in SMSY and there is a valid and working RFC conenction between Solman and the system you want EWA for defined the required place in SDCC. Please also check that the systems are visible in other scenarios in the graphic and indeed see if there is problems with specific systems
Also check
1) STI-PI and ST-A/PI is available on the system collecting EWA
2) SDCC has ran for the EWA and collected all the data
3) Nothing has been minimised or personalized in the DSWP screen
4) SICF services are activated and you can call the DSWP service from any (internal) user terminal - see note 834832
5) Nothing has been minimised or personalized in the DSWP screen
6) The model may need to be refreshed - may have to perform a rules update - see documentation on RDSWPRULESUPDATE
7) You are operating a recommended SP stack - see www.service.sap.com/sp-stacks
If these are all okay then it could be the setup of your EWA --->
If you are trying to setup your EarlyWatch on your Solution Manager system, then please visit the following URL:
and the following note
1257308 FAQ: Using EarlyWatch Alert
The following document is a BP on EWA setup on Solution Manager which will help you check configuration--->
http://www.service.sap.com/~sapidb/011000358700001873212008E
Best of luck
Stuart
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
93 | |
10 | |
10 | |
9 | |
9 | |
7 | |
6 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.