Short dump while executing job SM:EXEC SERVICES for EWA alert generation

[Former Member]

Hello All,

I'm getting short dump error while executing job SM:EXEC SERVICES for EWA alert generation.I'm using EHP1@SP22 of Sol Man.

Please find the logs

***************************************************************************************

Error in the ABAP Application Program

The current ABAP program "SAPLDSVAS_PROC" had to be terminated because it has

come across a statement that unfortunately cannot be executed.

The following syntax error occurred in program "RDSVASCABAP_TRANS__________073

" in include "RDSVASIABAP_TRANS__________073 " in

line 1782:

"Field "STATEMENT_SUMMARY001019" is unknown. It is neither in one of th"

"e specified tables nor defined by a "DATA" statement. "DATA" statement"

"."

" "

The include has been created and last changed by:

Created by: "SAP "

Last changed by: "SAP "

Error in the ABAP Application Program

The current ABAP program "SAPLDSVAS_PROC" had to be terminated because it has

come across a statement that unfortunately cannot be executed.

***************************************************************************************

If anyone came across such kind of dump, please reply asap, due to this, i could not generate EWA report for R/3 system 6.04.

Thanks,

Anand.

[Paul_Babier · Accepted solution]

Hi Anand,

You may find SAP Note 727998 helpful in this case.

Regards,

Paul

[Former Member · Accepted solution]

Thx Paul, but i already did checked this note and its not solving my issue

[Paul_Babier · Accepted solution]

>

> Thx Paul, but i already did checked this note and its not solving my issue

Dear Anand,

Did you perform a complete service definition replacement for SDCC/SDCCN as described in the note?

These are manual steps you need to perform on the system and are not code corrections.

I would suggest you perform it, if you have not, and check the SDCCN logs to review the process ran cleanly.

Note: Please make sure SDCC_OSS is functioning and a connection to SAP can be made before

deleting the service definitions.

If you have already replaced the service defintions on the Solution Manager system, then no point doing it again. However checking a note and applying it are not the same thing. So I am uncertain if you replaced the service definitions or not. The dump you are getting in SM:EXEC SERVICES suggests its due to a problem with the service definitons. The recommendation is to replace them according to the process described in SAP Note 727998. If you have not done so please do so.

If you have successfully replaced the service definitions are you still getting the same dump, or has it possibly changed?

Regards,

Paul

[Former Member · Accepted solution]

yes Paul, as per this note, i did checked my settings and i dont think so, anything to do with this.

To brief up, my SDCC_OSS connection is working fine and i'm sending this data through Refresh session to SOl Man system. I can see data is waited to pull up in Sol Man system through EWA report. Only issue for me is syntax error in that program/table, which is not able to execute further.

ANyways, thx for information.

[Former Member · Accepted solution]

HI Anand,

This note is the pnly solution of this problem.

Try to follow note completely also you can proceed as follow

Run SDCCN, choose Utilities -> Maintain Service Definitions.

Read below thread reply from Mr. Ruediger Stoecker

Regards,

[Paul_Babier · Accepted solution]

Anand

Did you follow these steps or didi you just schedule a refresh sessions task?

Please make sure you follow the steps outlined below

Path: SDCCN -> Utilities -> Maintain Service Definitions ->

Select 'Delete and Replace Service Definitions ->

Confirm this selection-> Confirm that you want to delete the definitions ->

Confirm that a new task 'Service Definition Refresh' was created ->

Take a note

of the task id ->

Review the log for this task id when it is completed.

You should not not see any errors for either the update of a Service

Definitions table or the generation of any re-import include.

If you do, then make note and post them here. Otherwise the error should be resolved.

Regards,

Paul

[Former Member · Accepted solution]

Thx Paul, i solved the problem after following the steps as per note # 727998

[Former Member · Accepted solution]

Thx Gagan to u too