E2E_EC_<SID> job not scheduled

[Former Member]

Hello,

As per my understanding after managed system setup wizard is run, Job: E2E_EC_<SID> job must be scheduled for data collection.

In my system I can see E2E_HK_CONTROLLER data collection controller running, but its not generating subsiquent job for data collection.

Spool output of E2E_HK_CONTROLLER as follows

22.02.2010 Program E2E_HK_CONTROLLER 1

Phase I: Aggregating Data

Target Infocube: 0DB6_C01D

Source Infocube: 0DB6_C01H

Destination : NONE

Aggregator :

E2E_HK_AGGREGATE_MDX

HK: Calling SMD_HOUSEKEEPER at NONE

HK: Cube aggregation: SMD_HK_AGGREGATE_MDX

Target Infocube: 0DB6_C01M

Source Infocube: 0DB6_C01D

Destination : NONE

Aggregator :

E2E_HK_AGGREGATE_MDX

HK: Calling SMD_HOUSEKEEPER at NONE

HK: Cube aggregation: SMD_HK_AGGREGATE_MDX

Target Infocube: 0DB6_C02D

Source Infocube: 0DB6_C02H

Destination : NONE

Aggregator :

E2E_HK_AGGREGATE_MDX

HK: Calling SMD_HOUSEKEEPER at NONE

HK: Cube aggregation: SMD_HK_AGGREGATE_MDX

Target Infocube: 0DB6_C02M

Source Infocube: 0DB6_C02D

Destination : NONE

Aggregator :

E2E_HK_AGGREGATE_MDX

HK: Calling SMD_HOUSEKEEPER at NONE

HK: Cube aggregation: SMD_HK_AGGREGATE_MDX

Target Infocube: 0DB6_C03D

Source Infocube: 0DB6_C03H

Destination : NONE

Aggregator :

E2E_HK_AGGREGATE_MDX

HK: Calling SMD_HOUSEKEEPER at NONE

.

.

.

.

.

22.02.2010 Program E2E_HK_CONTROLLER 5

E2E_HK_AGGREGATE

HK: Calling SMD_HOUSEKEEPER at NONE

HK: New Requests found:

APO_R4GWK0TDL2TTDKSX1FNF26WI2O

Target Infocube: 0SMD_PI2D

Source Infocube: 0SMD_PI2H

Destination : NONE

Aggregator :

E2E_HK_AGGREGATE

HK: Calling SMD_HOUSEKEEPER at NONE

HK: No new Requests found.

==================================================

Phase II: Deleting Data

Step 1: Selection Based Deletion

Deleting Data from 0SMD_ADCH Deletor ID: 1

Deleting Data from 0SMD_EA1H Deletor ID: 1

Deleting Data from 0SMD_EA2H Deletor ID: 1

Deleting Data from 0SMD_EA3H Deletor ID: 1

Deleting Data from 0SMD_EA4H Deletor ID: 1

Deleting Data from 0SMD_PE2H Deletor ID: 1

Deleting Data from 0SMD_PI2H Deletor ID: 1

Step 2: Consistent Hash Entry Deletion

Phase III: BI Housekeeping

Can any one tell me what does this mean ?

Regards,

Shyam.

[Former Member]

Good morning Shyam,

The job E2E_HK_CONTROLLER is the BI E2E Housekeeping job to aggregate the data for the E2E cubes in two phases:

Aggregate phase

u2013 E2E_HK_CONTROLLER

u2013 Daily basis (during the night)

u2013 List defined in table E2E_BI_AGGREGATE

Delete phase

u2013 E2E_HK_CONTROLLER

u2013 Daily basis (during the night)

u2013 List defined in table: E2E_BI_DELETE

The job to handle the data collection from the managed systems is the "EFWK Resource Manager (01 Minute)". This job runs every minute to check if some extractors are in the queue for execution. With SolMan Ehp1 this is the new way to collect the data and managed the extractors. Open your RCA work center go to Common Tasks -> Administration -> Extractor FWK Administration. The job creation for each managed system (E2E_EC_<SID> job) was the way prior release Ehp1.

Best regards,

Mike