on 08-31-2009 7:57 AM
Hello,
In SNP after executing Heuristic run it gives me error message "Invalid product-location combination (peagging Area)".
(/n/SAPAPO/SNP94)
can any body help me to reslove this issue.
Thanks,
Nikhil
Hi,
There seems to be a Master Data issue please run the following transaction in SE38
1) /SAPAPO/TS_LCM_REORG
2) /SAPAPO/TS_LCM_CONS_CHECK
Run all these settings with the tick on the Repair box
Also if required run the Consistency check before running the Heuristics again.
Please let me know if it heps resolve your issue.
Thanks,
Harsh
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Nikhil,
In Transaction /sapapo.mat1 go to the Demand Tab and click on the Pegging Tab under Demand Tab here ensure that every thing is blank. Tolerances % can be kept as 0.0%. Try doing these changes for a few materials run the Heuristics and Check.
Hope this will help in resolving your issue.
Thanks,
Harsh
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Nikhil,
Check the following.
1) Check all the components attached to finished product are attached to active version
2) Run a low level code /SAPAPO/SNPLLC followed by snp heuristic and retry
3) Check parallel processing is activated in customisation.
Regards
R. Senthil Mareeswaran.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
HI Nikhil,
Did you try what I had mentioned in my earlier message ?
Your data may be visible to you on the screen but the inconsistencies are in the LiveCache, you will have to run the Consistency checks for the Master data.
Thanks,
Harsh
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Harsh,
I have Run both the reports as mention by you
1)/SAPAPO/TS_LCM_REORG
2) /SAPAPO/TS_LCM_CONS_CHECK.
But same error message.
I have created my Model, planning version and copied all my Master,transaction from Active Model 000 and version 000 it is working fine without any error.
what can be the issue?
Thanks,
Nikhil
Hi Nikhil,
I suggest you check all your master data:
Do you have a valid PPM/PDS? (inluding if necessary phantom)
Are all your components active in the location and assign to model 000?
If you need, are transportastion lane OK?
You can try to create an order manually. See if you can, and if the order creatred is correct (e.g with a valide source of supply...). Then navigate to all components...
I hope it helps
Thanks and Regards
Julien
Hi Nikhil,
Did you try in mat1 transaction as I suggested earlier?
Regards
R. Senthil Mareeswaran.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Nikhil,
Goto transaction /sapapo/mat1, enter your location product and click on assign model
(Shift+F9), and assign your location product to the active version and then recheck
Regards
R. Senthil Mareeswaran.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Senthil,
It is already assign to Model 000 active model.
but i am not able to assign this to active planning version 000
it gives error message "No simulation parameters could be set for the active version".
i am getting error message in Heuristic run because of location product is not assign to active version 000?
Thanks,
Nikhil
Hi Nikhil,
Once your product location is assigned to Model 000 then automatically it will consider 000 version so you have done correctly. So ignore the error messages.
While executing SNP94, from the selection variant select only Product(don't select location). It will resolve your issue.
Regards,
Santosh Kumar Mishra
Hi Nikhil,
1) Check your executed location product is in the active model & version
2) Check using transaction /SAPAPO/RRP_NETCH whether pegging area exists
3) Check the material master of location product in APO whether all views are
maintained(especially pegging relevant fields)
Regards
R. Senthil Mareeswaran.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Senthil,
I have created pagging area for location product( planning version 000 /n/SAPAPO/RRP_NETCH ).
but i am not able to assign location product to planning version 000.
It is already assign to Model 000 active model.
I am getting error message "No simulation parameters could be set for the active version".
i am getting error message in Heuristic run because of location product is not assign to active version 000?
Thanks,
Nikhil
User | Count |
---|---|
7 | |
4 | |
3 | |
2 | |
2 | |
1 | |
1 | |
1 | |
1 | |
1 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.