Quality Score Calculation?

[former_member192718]

Dear SAPIENTS,

I need to know customizing setting for quality score calculation regarding vedor,characteristics,Usage decision etc.

Regards,

Kauhsal Rai

[former_member186399]

Dear Kaushal

1) Please let me know what is the weightage given for the MIC. whether is minor, major, critical etc. You can see this in Qs23.

Then accordinly check in config the adjacent quality score value

SPRO > QM> Quality Planning > Basic Data > Inspection Characteristic, Inspection Method > Define Characteristic Weighting

2) It is always better to calculate UD from select set. A typical example can be like this

01 001 Clean Acceptance A Accepted (OK) 100

01 002 Accepted subject to Rework R Rejected (not OK) 50

01 003 Accepted with deviation R Rejected (not OK) 70

01 004 Accepted after segregation (Partial qty) R Rejected (not OK) 60

01 005 Rejected R Rejected (not OK) 1

01 006 Accepted subject to functional test A Accepted (OK) 100

01 007 UD Changed due to line rejection R Rejected (not OK) 30

Regards

Gajesh

[former_member186399]

Dear Kaushal

In QA11 this field is not changeable. You can change this in QA12 . Also the UD score is given in the selected sets based on the UD code in QS51

Please check

Regards

Gajesh

[former_member192718]

Dear Gajesh,

In QS51 quality score 100 is maintained for good reciept. In material master weighted from quality score from characteristic is maintained. So from from characteristics score data 1 data is coming, how to check this?

Yes in QA12 i can change but i want auomatically from UD code.

Reagrds,

Edited by: Kaushal Rai on Aug 7, 2009 2:02 PM

[Former Member]

hi'

Qulity score calculation is related to Usage decision as in selected set we maintian UD code & corrosponding scores(QS51)

Also in QM view we maintian Quality score based on Usage Decision.

For more details ..........Quality score:

Revert back for more Querries

Regards

Sujit

[former_member186399]

dear Kaushal

Please find the detials below

Quality score are maintained for quantitative valuation of the quality of inspection lots.

1) They have to be first maintained in the client level setting

SPRO > QM> Maintain settings at client level> You need to maintain the highest quality score (100) and lowest quality score (1) system doesnt take 0. also Lower limit for good quality (90)

2) it is maiinly used in the selected sets for usage decision

QS51/ 03 catalogs for each UD code you can give a Quality score. So while you are giving UD system picks up this score and update the same for inspection lot , material, vendor, customer as applicable.

You can give 100 as quality score for clean acceptance, 1 for complete rejection, may be 50 for partial acceptance etc.

You can check for the reports in the information system.MCXE, MCVE, MCOE

3) There are different quality score adoption procedure ( defined by SAP)

SPRO > QM>Quality Inspection > inspection lot completion >Define quality score procedure

Share of scrap in lot

Maximum share of scrap for chars

Minimum quality score for chars

Weighted from share of scrap for chars

Weighted from quality score of chars.

From usage decision code

You can choose anyone and can be customised for inspection types these is done in

SPRO > QM>Quality Inspection > inspection lot Creation > Default values for inspection types> anyinspection type > inspection lot completion tab > Quality score procedure.

4) If you want to use quality score procedures that access the weighted shares of defects for the characteristics, you must maintain the characteristic weights.

SPRO > QM>quality Planning >Basic data> Inspection characteristic > define characteristic weighing > weight factor

If you want to use quality score procedures that access the quality score of the characteristics, you must maintain the defect classes.

SPRO > QM>quality Planning >Basic data>Catalog> Define defect class

If you want to use quality score procedures, in which the system calculates the share of scrap, you must:For this a) scrap share have been defined in Customizing .b)Assign suitable procedures for estimating the scrap share to the characteristics in the task list c)Identify inspection characteristics as relevant for scrap in their control indicators.

hope this helps

Regards

gajesh

[former_member192718]

Dear Gajesh,

You gave wonderful information. Now if you can tell why in my system at the time of UD giving default score 1 and that is non editable at the time of UD.

Regards,