on 05-05-2006 5:05 AM
Hi I am working on a File(Asyn)-RFC(Synchronos)-File(Asyn) using BPM. I have completed all the required steps in the IR and at the end of configuration in the Interface determination there was "<b>no inbound interface</b>" under the configured inbound interface. I have cross checked all the interfaces in IR. Also in the In the receiver agreement I <b>do not see any receiver interfaces</b>.
I have following message interfaces in IR.
1. Outbound file request.
2. File Request abstract
3. Inbound file response.
4. File response abstract.
5. File_Details for asynchrous.
BPM: receive- Synchronous Send- Send.
I am not sure what I am missing. Appreciate any one help on this.
Thanks
Steve
Message was edited by: Steve Holland
Hi,
Can you tell what are the configurations(Like the sender agreement, receiver determination etc...) created in ID.
Refer this weblog:
/people/arpit.seth/blog/2005/06/27/rfc-scenario-using-bpm--starter-kit
Regards
Suraj
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Suraj,
In fact I referred to this web log and crosschecked too and mine is almost the same. Still I am not sure where I am missing some thing
Receiver determinations:
1. File sender BS to BPM
2. BPM to R/3
3. BPM to File receiver.
Interface determination:
1. File Sender Outbound to File Request Abstract.
2. File Details Abstract MI to BAPI.
3. File Response Abtract to " NOTHING HERE" ??
I am suppose to get the File response MI here .
Receiver agreement BPM to R/3 is fine, but BPM to File response MI is not coming up.
Thanks
Steve.
Hi,
Some cross checks...
1) You are using Business system (for RFC) and Business Service (For file)??
2) Did you add your file MI 's to the appropriate Sender Receiever Tab of File Service?
3) What is the input and out MT of the AI used for communicating with RFC?
>>File response MI is not coming up
Add this MI in the <b>Receiver Tab </b>of the FileService
Regards
Suraj
Message was edited by: S.R.Suraj
Hi Steve,
Check once the message interfaces has been given correctly or not...
The interfaces u require is
1) Po_Out _async ( outbound,Asynchronous) for out file
2) po_async_abstract(Abstract,asynchronous)input to bpm
3) Po_sync_abstract (Abstract, synchronous)output of the BPM
4) po_resp_async_abstract (Abstract,Async)-- output from bpm to file
5) po_resp_in_async (inbound, asynchronous) response message to file
and also check the integration process check sender (po_sync_abstract,po_resp_async_abstract) and for receiver po_async_abstract) has been mentioned or not...
Hope this will work for the Int . determination correctly..
Regards,
Sridhar reddy
Message was edited by: sridhar reddy kondam
Hi,
For an inbound interface to RFC,no need to create a abstract interface.Create two inboubnd interface,one abstract interface for BPM and our normal synchronous inbound interface for RFC.
And try adding ur inbound interface in the interface determination.to talk to RFC u need an normal interface and the abstract interface is only for BPM.
In case if ur using business service add ur inbound interface in ur business service.
regards
jithesh
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
85 | |
10 | |
10 | |
9 | |
7 | |
6 | |
5 | |
5 | |
4 | |
3 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.