Upgrade our server RAM but not show in sap system (ST06)

[Former Member]

Dear All,

I have configure the transported down and getting an error

Dear all,

We are using Ecc5 and windows 2003 SP1 64 bit.We are going to upgrade our server RAM at present we have 8 gb and adding 8 gb mre ,total 16 Gb RAM.

After Ram is added in the server at os level it is showing .

*what changes I have to do that it will show in sap system (ST06) bze it is not showing there *

And PHYS_MEMSIZE 4908 set do i have to change this ..?

ST06 details

Memory

Physical mem avail Kb 8,376,136 Physical mem free Kb 1,756,928

Pages in/s 0 Kb paged in/s 0

Pages out/s 1,031 Kb paged out/s 8,248

Swap

Commit charge limit Kb 48,492,768 Maximum swap-space Kb 41,943,040

Commit charge free Kb 31,412,824 Actual swap-space Kb 41,910,272

Please suggest.

Regards,

Pallav

[Former Member]

Dear All,

Now RAM is showing in the St06 but getting error in in HpEventLog: Windows: Predictive Failure in Memory (25B4H) event log .Please find the details

We are using ecc5 on win 2003.

Event Type: Information

Event Source: WMIxWDM

Event Category: None

Event ID: 116

Date: 7/7/2009

Time: 1:03:48 AM

User: N/A

Computer: Description:

The memory page at physical address 276885487616 has encountered multiple corrected hardware error events. As a result it will no longer be used by Windows.

Event Type: Warning

Event Source: HpEventLog

Event Category: None

Event ID: 9652

Date: 7/7/2009

Time: 9:33:56 AM

User: N/A

Computer:

Description:

HP Event Log : [MSG_25B4] Windows: Predictive Failure in Memory - Location: DIMM slot 4B - Reporting entity: OS agent

Event Type: Error

Event Source: VolSnap

Event Category: None

Event ID: 16

Date: 7/6/2009

Time: 9:17:29 PM

User: N/A

Compute

Description:

The shadow copies of volume C: were aborted because volume M:, which contains shadow copy storage for this shadow copy, was force dismounted.

Event Category: None

Event ID: 109

Date: 7/6/2009

Time: 10:29:58 PM

User: N/A

Computer:

Description:

Corrected Machine Check Interrupt threshold exceeded. Interrupt has been disabled. Polling mode has been enabled.

Event Type: Warning

Event Source: HpPfmSvc

Event Category: None

Event ID: 1

Date: 7/7/2009

Time: 12:48:48 AM

User: N/A

Computer:

Description:

A Corrected Machine Check (or Corrected Platform Error) error of an unknown variety was observed by the PreFail Monitor. This error was corrected and no action is necessary, but if this condition repeats contact HP for support guidance.

And also Alert mail

The system has detected the following event:

SNMP Trap: 9652

Date time: 07/07/2009 09:33:56 AM

Computer:

Source: HpEventLog

Type: Warning

Category: (0)

Description:

You will receive this message if the system is correcting a lot of ECC single bit errors. It may mean that the module is about to fail, or environmental conditions in the server are causing more errors than usual. If you receive this message, contact your support provider to determine if a predictive repair should be made.

Details:

For more details, look at the System Event Log.

Please suggest how to solve this problem.

Regards,

Kumar

[Former Member]

There seems to be a problem with your RAM module. I suggest you to contact hardware vendor to correct the problem.

[Former Member]

Hi Kumarmoh,

Just stop your SAPOSCOL and restart the same, after getting restarted check and revert.

Before going to restart just check whethre at os level it is showing correct or not?

Regards

Nick Loy

[Former Member]

Hi,

There is no place in SAP where you need to add the RAM manually to show in ST06.

It will refelect as soon as RAM is upgraded.

Can you cross check the SAPOSCOLL program, whether it is running and shared memory is available.

Try to clear the shared memory of the saposcoll and check.

use saposcoll -d command to go to dialoge mode of saposcoll and clear the shared memory.

Regarding the phy_mem parameter which need to be set in case of windows env, as it is checked in case of Windows env.

The parameter PHY_MEM is nothing to do with the SAPOSCOLL.

Thanks & Regards,

Balaji.S

[Former Member]

Hi,

Thanks for suggestion that mean once RAM is add in the server it will show in ST06 also But in my server it has not shown

Memory

Physical mem avail Kb ---

but at OS level it is showing 16 Gb but in sap System old value 8 gb only.

and SAPOSCOLL is running and i have restared the server after adding the RAM

Please suggest how to solve this problem.

Regards,

Kumar

[Former Member]

HI

Check the service saposcol is running fine

Regards

Uday

[sunny_pahuja2]

Hi,

Check below link:

http://help.sap.com/saphelp_nw70/helpdata/EN/84/7ed384d81f11d188be0000e83539c3/content.htm

Thanks

Sunny