STO -STOCK IN TRANSIT- SCRAP issue

[Former Member]

Hi

I hane done STO from PLANT 1 to PLANT 2...Material Qty 10,000 lit

cretae sto in ME21N

then do the outbound delivery goods issue from plant1

now stock in transit..

do the GR against STO .. here GR qty 9950 lts(actual )

remaining 50 lit leacked while come throut tanker....

in plant 2 GR has doen for 9950 lits only

when i see the stock in tannsit repot.. display the pending material 50 lit...

actually this is leackage stock.. how can remove this lecakge stok from stock in transit..

pls.. guide about this issue

regards

sesidhar

[Former Member · Accepted solution]

Hi,

The adjustment can be done using MB1A 557 movement type which is designed for such adjustments in SAP - "Issue from stock in transit (adjustment posting)"

Regards

Merwyn

[Former Member · Accepted solution]

Hi

TANKU .. I have done according to u r guidelines... stock posted.. with 557 movtype in MB1A

but ..again..... i this stock has shown in transit stock repot mb5t..

regards

sesidhar

[Former Member]

Hi,

Refer to the SAP Note 389484 - Movement types 557/558 for the stock in transit correction,

also Note 392205

Check whether program RM07APP1 exists in your system and the date "12.01.2001" is contained in the comment block at the program start.

If this is not the case, use Note 198596 to import the program in a current version.

Note 392205 - Analysis of stock in transit/correction for split valuation

Symptom

SAP Support: Please read the remark to the note!

o Goods receipt for stock transport orders cannot be posted as the

system reports a deficit in the stock in transit (Message M7

021/022).

o Materials show stock in transit although there are no longer any

open stock transport orders.

Caution:This note only refers to real stock in transit and not to

virtual stock in transit in cross-company stock transport orders.

Counter-indications

The procedure in this note (movement types 557 nd 558) must not be followed

to "correct" genuine database inconsistencies in the stock in transit

which, for example, have arisen due to incorrect updates. Proceed as in

Note 32236.

Additional key words

Stock transport order, stock transfer, MARC-TRAME, MSSA-SATRA, MSSQ-SQTRA,

stock in transit, TRAME, M7021, M7022, MvT557, MvT558, 557, 558,

correction, MMINKON

Cause and prerequisites

The R/3 system is designed so that the stock in transit can only be posted

through stock transport orders (creation during goods issue, reduction

during goods receipt).

Purchase order and material master record can have different units of

measure. The purchase order is then closed when the goods issue quantity

and quantity of goods received are the same in order unit. However, in the

material master record, the stock in transit is managed in the base unit of

measure.

On account of system-dependent and program-internal rounding effects which

cannot be avoided, the open stock in transit quantities in order unit and

in base unit of measure might not balance to zero at the same time.

Regards

Merwyn

[Former Member]

Hi,

leakage stock you can issue as a scrap ,

or goods issue to cost center

[Former Member]

Hi,

Check if the 557 document has been posted in MB51 report,

If 557 is posted for the differential qty, then it should not be appearing in your MB5T report

Regards

Merwyn

[Former Member]

Hi

I have checked in mb51 557 posting is there... but this is only in plant not in storage location..

1)i did (me21n )STO

2)did the deliver gainst P.O.. and PGI also for 10,000 lits

3) did the GR against to Outbound delivery.. for 9950 only..

4) goto mb5t .. 50 lits... stock in transit.. ok

5) now goto MB1A.... GI for stock in transit adjustment 557 movtype..

here input valuse.. material , qty 50 lit , plant 2, batch , cost centre, storagelocation did not taken...

then post the document ... document posted..

then see the document in MB51.... ...material document displayed(with in put parameters..plant,material movtype,).....with movtype 557...

material document didnot displayed in mb51 (input parameters..plant, stroagelocation, movtype,material )with movetype557

6)then goto MB5T ... here displayed stockin transit for 50lits..

7) pls... giude me in this issue....

[Former Member]

this can be done in 2 ways

recieve the full value in recieving plant and scrap the goods , here the scrapping is posted on value in recv plant

else reverse the Goods issue doc and scrapp from issue plant , value of scrap will now be from issue plant

[Former Member]

Make GR at receiving plant for full quantity.

from Mb1a make "stock transfer or tranfer posting" for 50 litres to scrap.

movement type:551

[Former Member]

Hi

thanku

This is I know ... i want to do directly remove from transit stock....is it possible?

regards

sesidhar

[former_member190537]

Hello,

Yes you can directly remove the stock from Stock in transit with help of movement type 557 to Overhead cost center or Scrap it.

Regards

Mahesh Naik.

[Former Member]

No. As we can not storage location for stock in transit.

[Former Member]

I think direct removal is not possible.

I also tried but can not find any solution.