on 02-25-2009 4:02 PM
Dear Tech Masters,
Our data centre located in Singapore, I have installed SAP router in the Landscape. I am using SNC. Is that mandatory to use "sapserv2" (SAP network support server) for connection Or I can use the "sapserv7" of Singapore. As mentioned in service market place "sapserv2" is for SNC Global and sapserv7 is Singapore server. I am confuse over this.
This is my first SAP Router installation. Please help me.
Regards
Rabi Pal
Hi,
Nope i dont think it is mandatory.
Regards,
Vamshi.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hello Rabi,
For setting up the connection to SAP:
Choose a connection type and apply for your connection.
Provide SAP with the data it needs to set up the connection between your SAProuter system and the SAP support server using the Remote Connection Data Sheet (SAP Note 0028976).
Configure your network components (SAProuter).
Once a remote connection is established, enter the required logical connections between your R/3 systems and SAP. You will find a description of this procedure in SAP Note 31515.
Also you can refer to https://websmp105.sap-ag.de/saprouter.This will give you alll the info. you want about SAP router
Let me know if you have any questions
Rohit
Hello Rabi,
Please find the guide for setting up SAP SNC Router connection at the following link
I am sure it will be helpful
http://www.erpgenie.com/sapgenie/docs/SAP%20SNC%20CONFIGURATION.pdf
Rohit
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
In addition to above also make sure you add correct sapserv# ip address in RFC detsination SAPOSS.
Hope this helps
Thanks,
Sushil
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
using sapserv2 is not mandatory. You can use sapserv7..
Regards,
Jazz
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi ,
I am using SNC , I have done with all configuration and sent data sheet to SAP. If I change CN=sapserv7 in saproutab as :
#SNC-Connection from and to SAP
KT "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 194.39.131.34 *
KT "p:CN=sapserv7, OU=SAProuter, O=SAP, C=DE" 194.39.134.35 *
Will that work.
where as in service market place Target is showing as sapserv1. Do I need to change this as well ..??
SAProuter Name Distinguished Name (Parameter for SAPGENPSE) Target (on SAP-side)
CustSAPRouter CN=SAPRouter, OU=*********, OU=SAProuter, O=SAP, C=DE sapserv1
Please suggest.
Regards
Rabi Pal
Hi,
Please check below SAP notes.
30289 - SAProuter documentation
17285 - Logon to OSS (Transaction OSS1)
33135 - Guidelines for OSS1
766505 - OSS1: Changes to the RFC connection to SAPOSS
Hope this helps.
Thanks,
Sushil
Edited by: Sushil Suryawanshi on Feb 26, 2009 2:54 AM
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
90 | |
10 | |
10 | |
10 | |
7 | |
7 | |
6 | |
5 | |
4 | |
3 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.