on 11-14-2008 9:11 AM
Hi All,
Iam doing Idoc to Idoc Scenario from Dev System to Quality System using the WP_PLU (Atricle Master).
I wish to send the same Idoc from DEV to QTY with the partner Type KU
Check List which i have done
In R/3
1) Create RFC Destination in DEV which points to XI
2) Created Port using the above created RFC Destination
3) Created Outbound Partner Profile of Type Customer (KU) Ex; C002
In XI
1) Created RFC Destination Towards DEV to load the metada of Idoc
2) Created RFC Destination Towards QTY to send the Idoc
3) Created Port in IDX1
In Receiving System
1)Created Inbound Partner Profile of Type KU, Ex: S002
Every thing is flowing correctly
1) Generated the Outbound idoc in DEV system
2) got the messages in XI side in MONI
3) Received the Idoc at Receiver System with Error saying that Partner Profile not available
But i created the Inbound PF in Receiving system Under KU Type.
Here the Idoc Control record values are getting filled up by defauly with Type LS not able to load type KU here.
That is why the Idoc unable to Identify the Partner in Receiving system.
What might be the solution here to overcome the Error
Regards
Seshagiri
Hi,
Since default is LS, so for KU you need to define it in CC. Follow the link provided by Chirag. And if your mapping is 1:1 then no need of doing the mapping.
Regards,
Sarvesh
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
Did u configure the identifier with KU in communication channel.
refer the below pdf
chirag
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Chirag,
I want to pass these following details to the receiver Idoc Control Record, then only the Idoc get posted Successfully in the Recer side
1) Sender Partner Number Ex:(S002)
2) Receiver Partner number Ex:(C002)
3) Sender Type as KU
4) Receiver type as KU
But in the document which you have provided is saying that we have to mention the Partner Number Once we create the Party.in that we can mention the Number
But my case is not Party, this is with out party. iam just sending the idoc From One Server to another
Even i just mentioned the Partner Type for sender & Receiver as ALE#KU in the Identifier TAB of Receiver Idoc Channel.And iam getting the same Error and not getting updated with Type KU in Control record values
Regards
Seshagiri
Hi N V Seshagiri
Sorry for delay in reply.
I have checked my scenario and it was file to IDOC.
Below configuration was done.
Source Partner Type : KU
Receiver Partner Type : LS
I have used Party for sender system and mentioned the below information in party identifier tab.
File confirguration
Agency:Business service name
Schema: ALE#KU
Name: partner no
For IDOC configuration no party was used as rec partner type was LS.
but in IDOC communication identifier tab i have mentioned sender information as below
Agency; Business service name
Schema: ALE#KU.
I think for ur case
u need to use the party for both sender as well as Rx.
U have to mentioned the party identifier information and in IDOC communication identifier tab u need to put the RX information aswell.
chirag
Hi,
Thanks for the Update,
Here my scenario is i have Two SAP Systems say System A & System B
I have to send One Idoc data from System A to System B( means Store A to Store B)
then this time both will have the Type of KU only. I have to pass the sender details as well as the receiver details manually, then only default details like LS will take place by KU.
You said that i have to use Party at both the ends, will it fit for this situation??
Okay , let me try the Solution of using the Party for both Ends and i will pass sender & receiver details through party identifier tab for both.
Regards
Seshagiri
User | Count |
---|---|
88 | |
23 | |
11 | |
9 | |
8 | |
5 | |
5 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.