cancel
Showing results for 
Search instead for 
Did you mean: 

oss1 route permission denied to xx.xxx.xxx to oss1sammsoss

tarkan_atesoglu
Explorer
0 Kudos

hi gurus ,

ı have an error when ı got the rfc saposs ı have a saprouttab

ı add to this both ip saprouttab

this error

Error Details eRROR: sapserv2a: route permission denied (xx.xxx.xxx.xxx to oss001, sapmsOSS

can anyone help me?

Accepted Solutions (1)

Accepted Solutions (1)

Former Member
0 Kudos

Hi,

Make entries for sapserv2 in your routtab.

Regards,

Vamshi.

tarkan_atesoglu
Explorer
0 Kudos

ı have a entries sapserv2

Former Member
0 Kudos

Hi,

You should have two entries one for in comming connection and other for out going connection.

Regards,

Vamshi.

Former Member
0 Kudos

Hi,

Can you paste the details of your saproutttab. and the entries as in "technical setting tab" in Tcode oss1.

Regards,

Satyabrat

tarkan_atesoglu
Explorer
0 Kudos

prodeaserver

192.168.2.54

99

sapserv1

194.39.131.34

99

Former Member
0 Kudos

Hi,

This entries in the routtab are not sufficient if you are using the SNC router,

However SAP is not supporting non snc router permissions.

Also the port number should be 32xx and 36xx.

Regards,

Vamshi.

Former Member
0 Kudos

Hi,

You have given the details of the tcode oss1.as your error is saying that "rout permission denied" I need to check the entry of your saprouttab.

Your entry should be as follows.

  1. SNC-connection from and to SAP

KT "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" 194.39.131.34 *

  1. SNC-connection from SAP to local R/3-System for Support

KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" <R/3-Serverlocal IP address>*

KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" <R/3-Serverlocal IP address>*

KP "p:CN=sapserv2, OU=SAProuter, O=SAP, C=DE" <R/3-Serverlocal IP address>*

  1. here you can maintan your entry of yor sap systems (above example is for three systems)

P 194.39.131.34 *

  1. above you r providing the access only to sapserv2. If you want you can mantain perticular IP addresses also

  1. All other connections will be denied

D * * *

Try this and let me know if you have any issue on this.

Regards,

Satyabrat

Answers (1)

Answers (1)

Former Member
0 Kudos

Troubleshooting point of you

You can set the entries in routab as

P * * * *

Allow all out going and incomming sessions.

Stop the router and start it.

Set the trace level 3 with option -V 3

and check the trace.

Hope this helps you.

Amit Asthana

Former Member
0 Kudos

Hi,

A P * * * entry would not help you to connect to the oss systems.

Because SAP does not support non SNC routers anymore.

Regards,

Vamshi.

Former Member
0 Kudos

Hello Mr. vamshi polasa.

Can you provide link where you find this information? We use non SNC saprouter now, and it works fine...

Regards.

Former Member
0 Kudos

Hi,

You can find the info i nthe market place,

Also recently we have installed new router, and raised a support message for the registration and got a reply that we have to use the SNC router only.

Regards,

Vamshi.