Abap Proxy settings!

[Former Member]

Hi Friends,

I was woking on the Abap Proxy scenerio ( Server Type). I was going through the link

, and this was great.

I hav still not started, but I hav a question.

I cannnot see the Software components and name spaces of the Integration Repository in the SPROXY transaction in my R/3 system. As per the URL

, Design Time - point No 2 , can any 1 tell me which/ which all specific settings enable the availability of the software components and name spaces to be availabe in the SPROXY transaction of the R/3 server!

Regards,

Arnab

[Former Member]

Will come back with more relevant queries!

[Former Member]

Hi,

In XI & in R3 by using tcode SXMB_ADM, you need to configure the Integration System & Application System in respictive systems.

Take the help of this blog, for pxoy connect this blog is very useful. Follow all the steps...

Regards,

Sarvesh

[Former Member]

Sarvesh,

i hav folwed the URL

at the very begining. All the 3 RFC connections are working fine, I donno why is it still not working .

SXMb_ADM settings done .... !

Gaurav Bhargava ,

I am using PISUPER id and its has super access, i hope this wont be a problem, as it is far more

authoriesd trhan XIAPPLUSER.

REGARDS,

Arnab

[VijayKonam]

You must have created your software component as SAP.com or sap as vendor. Change that to something else in your SLD. You will see them.

VJ

[Former Member]

Refresh the cache and then try.. if all the settings have been done then it should work.

Just to make sure if cache is updating properly, check in XI by tcode SICF if all the services are active.

Regards,

Sarvesh

[Former Member]

HI

Did your SWCV has SAP as vendor then change it to something else

Check this

Refresh the caches see if any error....... Sometimes this can be the issue.

Thanks

Gaurav

[Former Member]

Hi,

see i cannot change the SCV now, as implementation is already done, is it mandatory...are you sure, because, in a different project, the vendor name as well as SCV is SAP.COm, but still is working,.....and see, my scenerio is ABAP Clent proxy, and in the R/3 system, SPROXY transaction -->GO TO --> Connection test , I get the following :

Check List for Setting Up a Connection to the Integr

1. The address of the Integration Builder must be stored in teh

system

=>Check/maintain with report SPROX_CHECK_IFR -- Tested positiev except for that fact taht SPROXSET table is empty?? but is it mandatory??

The address is taken from the following para

profile ('Connections' section):

com.sap.aii.connect.repository.name: Server

com.sap.aii.connect.repository.httpport: Por

com.sap.aii.connect.repository.contextroot:

The logon data is also read from the exchang

('ApplicationSystem' section):

com.sap.aii.applicationsystem.serviceuser.na

com.sap.aii.applicationsystem.serviceuser.pw

If no address is found, then an HTTP destina

table SPROXSET, which already contains these

information:

Column NAME: "IFR_HTTP_DEST"

Column VALUE: for example, "MY_DESTINATION"

The destination must have been created using transaction SM59.

For the repository URL "http://myserver:4711/rep", for example, the

following values must be maintained:

Connection type: "G" Target host:"myserver" Service No:"4711" Path

prefix: "/rep"

User and password accordingly.

If maintained, the settings from the exchange profile are always

used. If you want to deviate from this and only take the address

from the table SPROXSET, you must enter ADDRESS_ONLY_FROM_SPROXSET =

"X".

2. The HTTP connection of the ERP application server must

correctly

=>Check with report SPROX_CHECK_HTTP_COMMUNICATION

If necessary, contact your system administrator. The H

the ERP application server may be configured incorrect

Alternatively, you can log on to another application s

system where the HTTP port is functioning correctly. I hav made this -- tested OKK

3. The Integration Builder server must be running c

=>Check with report SPROX_CHECK_IFR_RESPONSE

(This link should display a valid XML document,

with 'Page Not Found', 'Internal Server Error 50

If necessary, contact your system administrator,

Integration Repository server, or import the cor

release. ok.. showing all the IR software component version names in XML Pls note this is important, indicating, some kind of coonetivity HAS occured !!

4. Proxy generation must interpret the data of the

correctly

==>Check with report SPROX_CHECK_IFR_CONNECTION -- OKK

Pls suggest something!

Regards,

Arnab !

[Former Member]

Hi Arnab,

U need to connection between the XI & R/3 systems. Once its HTTP & RFC connections is their its showing the SPROXY.

Regards,

Sateesh N.

[samiullah_qureshi]

Hi,

1. Plz check SAPSLDAPI and LCRSAPRFC RFC destination on R3.

2. Check data transaction SLDAPICUST is maintain correctly for sld.

3. Also check whether attached integration server is maintain in transaction SXMB_ADM. If not then maintain it. If not then maintain is under category Runtime, Parameter IS_URL and then the put URL for integration server in default value.

If those things are fine then run SLDCHECK transaction in R3 it should logon to the sld of XI.

Regards,

Sami.

[former_member184619]

Hi Arnab,

Check this

https://websmp202.sap-ag.de/~sapidb/012006153200000920262007E/Readiness_Check_Version4.pdf

Market place ID required to access.

Regards,

Sachin

[Former Member]

first establish the RFC connections http/tcpip, from XI to R/3 and R/3 to XI

[Former Member]

Hi,

You need to create HTTP connection your systems.

Go through the blog and do the required settings as mentioned in the Blog.

[Former Member]

HI

Did you created the RFC destination type H. IF yes is it working fine. Just check

Refer this blog as well this will help

Thanks

Gaurav

[Former Member]

Hi,

On running the transaction SLDCHECK, in my R/3 system, I am hetting this error.

Summary: Connection to SLD does not work

=> Check SLD function and configurations.

When testing the connection for SAPISU_XID, I am getting the error as

ICM_HTTP_Connection_Failed .

When, in my r/ I go to the SXMB_ADM - Integration Engine Configuration data and try for System Landscape - Load Configuration -- I get the messege "

No Access To system landscape at present!"

Any feeds!

Regards,

Arnab !

Edited by: Arnab Mondal on Oct 20, 2008 7:19 AM

[Former Member]

HI

Check with the PIAPPLUSER and PIISUSER authentication. These need to have basic SLD access authorization

Follow this thread you can get more steps

Old troubleshooting guide which always helps

https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/bd5950ff-0701-0010-a5bc-86d45fd5...

Thanks

Gaurav